V-102-1A4 Datasheet, PDF (14/16 Pages) List of Unclassifed Manufacturers – Miniature Basic Switch

V
Miniature Basic Switch
Thermosetting Case (V-15/V-10 Models) Applicable to both Standard (80°C) and Heat-resistive (150°C) models
The following dimensions and Operating Characteristics are for both "Not specified: Standard (80°C)" and "-T: Heat-resistive (150°C)" models.
The following illustrations and drawings are for COM bottom position and solder terminals (Terminal A). V models with a switching current of 15A and 10A have screw
terminals (B) and quick-connect terminals #187 (C2). These models are different from #250 models in terminal size only.Illustrations for screw terminals (B) and
quick-connect terminals #187 (C2) are omitted. Please refer to "Terminals and Shapes" on page 8.
The @ is replaced with the code for the terminals.See the "List of Models" for available combinations of shapes.
●Pin plunger
V-15-1@6
V-15-1@5
V ^V-10-1@5
V-10-1@4
20.2±0.25
PT
2.8
A
2.8
OP _10.3±0.1
φ3.1^{+−00..1033} hole
15.9 _18.8
4.2 2.8
3.1_{−+00..0133}
φ3.4±0.15
22.2±0.1
27.8
37.8±0.8
2.8
(10)
10.3
Three, solder terminals
#187 (t0.5)
Operating
characteristics
OF max.
RF min.
PT max.
OT min.
MD max.
OP
Model
V-15-1@6
V-15-1@5
V-10-1@5
V-10-1@4
3.92N
078N
1.96N
0.49N
0.98N
0.20N
1.2mm
1.0mm
0.4mm
14.7±0.4mm
●Short hinge lever
V-151-1@6
V-151-1@5
V-101-1@5
V-101-1@4
PT
2.8
OP _10.3±0.1
t=0.5 *
A
22.1
8.1
φ3.1^{+−00..1033} hole
15.9 _18.8
4.3 2.8
3.1_{−+00..0133}
φ3.4±0.15
22.2±0.1
27.8
37.8±0.8
2.8
(10)
10.3
Three, solder terminals
#187 (t0.5)
* Stainless-steel lever
Operating
characteristics
OF max.
RF min.
PT max.
OT min.
MD max.
OP
Model
V-151-1@6
V-151-1@5
V-101-1@5
V-101-1@4
3.92N
0.49N
1.96N
0.49N
0.98N
0.15N
1.6mm
0.8mm
0.6mm
15.2±0.5mm
●Hinge lever
V-152-1@6
V-152-1@5
V-102-1@5
V-102-1@4
PT
A
2.8
OP
10.3±0.1
t=0.5 *
35.6±0.8
8.1
φ3.1^{+−00..1033} hole
15.9 _18.8
4.3 2.8
3.1_{−+00..0133}
Ǿ3.4±0.15
22.2±0.1
27.8
37.8±0.8
2.8
(10)
10.3
Three, solder terminals
#187 (t0.5)
* Stainless-steel lever
Operating
characteristics
OF max.
RF min.
PT max.
OT min.
MD max.
OP
Model
V-152-1@6
V-152-1@5
V-102-1@5
V-102-1@4
2.45N
0.25N
1.23N
0.14N
0.59N
0.06N
4.0mm
1.6mm
1.5mm
15.2±1.2mm
●Long Hinge Lever Models
V-153-1@6
V-153-1@5
A
V-103-1@5
PT
V-103-1@4
2.8
OP
10.3±0.1
t=0.5 *
59.4±0.8
8.1
φ3.1^{+−00..1033} hole
15.9 _18.8
4.3 2.8
3.1_{−+00..0133}
φ3.4±0.15
22.2±0.1
27.8
37.8±0.8
2.8
(10)
10.3
Three, solder terminals
#187 (t0.5)
* Stainless-steel lever
Operating
characteristics
OF max.
RF min.
PT max.
OT min.
MD max.
OP
Model
V-153-1@6
V-153-1@5
V-103-1@5
V-103-1@4
1.27N
0.12N
0.69N
0.06N
0.34N
-
9.0mm
2.0mm
2.8mm
9.0mm
3.2mm
2.8mm
15.2^+−23^..26 mm
15.2±2.6
mm
Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
14