V-102-1A4 Datasheet, PDF (12/16 Pages) List of Unclassifed Manufacturers – Miniature Basic Switch

V
Miniature Basic Switch
Dimensions and Operating Characteristics
Thermoplastic Case V-21/-16 Models
The following illustrations and drawings are for COM bottom position and quick-connect terminals #250 (terminals C). V models with a switching current of 16 A and
11 A incorporate solder terminals (A) and quick-connect termimals #187 (C2). These models are different from #250 models in terminal size only. Dimensions of solder
terminals A, quick-connect terminal #187 (C2) and COM side position are omitted. Please refer to the "Terminals and Shapes" on previous page.
The @ is replaced with the code for the terminals. See the "List of Models" for available combinations of shapes.
●Pin plunger
V-21-1@6
V ^V-16-1@6
V-16-1@5
A
PT
2.8
2.8
OP _10.3±0.1
20.2±0.25 _1.6
φ3.1^{+−00..1033} hole
15.9 _19.1
4.2 2.8
3.1_{−+00..0133}
φ3.4±0.15
22.2±0.1
27.8 ^{2.8 (12.0)}
39.8±0.8
10.3
Three, quick-connect
terminals (#250) (t0.8)
Operating
characteristics
OF max.
RF min.
PT max.
OT min.
MD max.
OP
Model
V-21-1@6
V-16-1@6
V-16-1@5
3.92N
0.78N
1.96N
0.49N
1.2mm
1.0mm
0.4mm
14.7±0.4mm
●Short hinge lever
V-211-1@6
V-161-1@6
V-161-1@5
PT
2.8
OP
10.3±0.1
22.1
A _{t=0.5 *}
8.1
1.6
φ3.1^{+−00..1033} hole
15.9 _19.1
4.3 2.8
3.1_{−+00..0133}
φ3.4±0.15
22.2±0.1
27.8 ^{2.8 (12.0)}
39.8±0.8
Three, quick-connect ^10.3
terminals (#250) (t0.8)
* Stainless-steel lever
Operating
characteristics
OF max.
RF min.
PT max.
OT min.
MD max.
OP
Model
V-211-1@6
V-161-1@6
V-161-1@5
3.92N
0.49N
1.96N
0.49N
1.6mm
0.8mm
0.6mm
15.2±0.5mm
●Hinge lever
V-212-1@6
V-162-1@6
V-162-1@5
PT
A
2.8
OP
10.3±0.1
35.6±0.8
t=0.5 *
8.1 ^1.6
φ3.1^{+−00..1033} hole
15.9 _19.1
4.3 2.8
3.1_{−+00..0133}
φ3.4±0.15
22.2±0.1
27.8 ^{2.8 (12.0)}
39.8±0.8
Three, quick-connect ^10.3
terminals (#250) (t0.8)
* Stainless-steel lever
Operating
characteristics
OF max.
RF min.
PT max.
OT min.
MD max.
OP
Model
V-212-1@6
V-162-1@6
V-162-1@5
2.45N
0.25N
1.23N
0.14N
4.0mm
1.6mm
1.5mm
15.2±1.2mm
●Long Hinge Lever Models
V-213-1@6
A
V-163-1@6
V-163-1@5
PT
2.8
OP
10.3±0.1
59.4±0.8
t=0.5 *
8.1 ^1.6
φ3.1^{+−00..1033} hole
15.9 _19.1
4.3 2.8
3.1_{−+00..0133}
φ3.4±0.15
22.2±0.1
27.8 ^{2.8 (12.0)}
39.8±0.8
Three, quick-connect ^10.3
terminals (#250) (t0.8)
* Stainless-steel lever
Operating
characteristics
OF max.
RF min.
PT max.
OT min.
MD max.
OP
Model
V-213-1@6
V-163-1@6
V-163-1@5
1.27N
0.12N
0.69N
0.06N
9.0mm
2.0mm
2.8mm
15.2^+−23^..26 mm
Note 1. Unless otherwise specified, a tolerance of ±0.4 mm applies to all dimensions.
Note 2. The operating characteristics are for operation in the A direction ( ).
12