YS05S16-0G Datasheet, PDF (12/23 Pages) List of Unclassifed Manufacturers – GPS Module TC6000GN-P1

GPS Module TC6000GN-P1
Datasheet V022
confidential information preliminary specification
NO
2F
1F
4C
3D
2E
3C
1E
NAME
VDD_IO
VBAT
DEBUG_RESET_n
GND1
GND2
GND3
TCXO_CLK
TYPE¹
P
P
I
P
P
P
O
DESCRIPTION
Power-Management Signals
1.8V I/O power supply voltage
1.8V main power supply voltage
Connect to GND
Common Ground
Common Ground
Common Ground
Clock Signals
TCXO_CLK signal output. This Pin delivers the high stable TCXO frequency of 26.000
MHz for external components. Although the output is buffered, do not load this pin
below 20kOhms // 10pF(TBD). Leave open if not used.
6F
RTC_CLK
3A
GPS_RF
2A
GPS_GND1
4A
GPS_GND2
6B
GPS_PPS
6E
ON_THE_FLY_PRG
6A
PUSH_TO_FIX
5A
FIX_AVAILABLE
5F
GPS_RESET
1A
NU12
1B
NU1
2B
NU2
3B
NU3
4B
NU4
5B
NU5
5E
NU10
4D
NU7
5D
NU8
6D
NU9
5C
NU11
6C
NU6
I
Clock input: 32.768 kHz. Input for an external low frequency clock signal.
A clock must be provided at this pin to operate the module. See chapter "RTC
CONNECTION"
GPS Signals
Ana
GPS RF Input, direct connection of passive or active GPS antenna
P
GPS RF Ground
P
GPS RF Ground
O
This output delivers a high-precision pulse-per-second signal that is synchronized to
the GPS time reference. The pulse precision is better than 1*10^-7 seconds. Although
the output is buffered, do not load this pin below 10kOhms // 47pF (TBD). Leave open
if not used .
I
This input determines operation after reset. Internally pulled up for normal operation.
pull low for re- programming firmware or reconfiguring the module. Leave open in
normal operation.
I
Input signal to switch between operation and deep sleep mode. internally pulled down.
pull high (with less than 4.7kOhm) during operation. pull low (or leave open) to set
the module to deep sleep. Internal RTC continues to work in deep sleep.
O
This pin indicates a fix position.
Leave open if not used.
I
Main Reset for the receiver. Internally weak pulled down. Pull high with less than
100kOhm for operation. pull to GND (or leave open) during power – up.
NOT USED PINs DO NOT CONNECT
do not connect
do not connect
do not connect
do not connect
do not connect
do not connect
do not connect
do not connect
do not connect
do not connect
do not connect
do not connect
UART
3F
GPS_UART_TX
O
Main UART TX.
4F
GPS_UART_RX
I
Main UART RX.
3E
GPS_UART_CTS
I
Main UART CTS. CTS not used. Leave open
4E
GPS_UART_RTS
O
Main UART RTS. not used . Must be left open
I2C
1D
DB_1
must be connected to DB_2
2D
DB_2
must be connected to DB_1
1C
DB_3
must be connected to DB_4
2C
DB_4
must be connected to DB_3
(1) I = INPUT; O = OUTPUT; I/O = BIDIRECTIONAL; P = POWER PIN; ANA = ANALOG PIN.
12
© GNS-GmbH 2011
V 0.22, Sep5^th 2012