|
SEN01G64D1BF1SA-25R Datasheet, PDF (1/14 Pages) List of Unclassifed Manufacturers – 1GB DDR2 – SDRAM SO-DIMM | |||
|
Data Sheet
Rev.1.2 12.12.2010
1GB DDR2 â SDRAM SO-DIMM
200 Pin SO-DIMM
SEN01G64D1BF1SA-xxR
1GByte in FBGA Technology
RoHS compliant
Options:
ï§ Data Rate / Latency
DDR2 667 MT/s CL5
DDR2 800 MT/s CL6
Marking
-30
-25
ï§ Module Density
1024MB with 8 dies and 1 rank
ï§ Standard Grade (TA)
(TC)
Grade E
(TA)
(TC)
Grade W
(TA)
(TC)
0°C to 70°C
0°C to 85°C
0°C to 85°C
0°C to 95°C
-40°C to 85°C
-40°C to 95°C
* The refresh rate has to be doubled when 85°C>TC>95°C
Environmental Requirements:
ï§ Operating temperature (ambient)
standard Grade
0°C to 70°C
Grade E
0°C to 85°C
Grade W
-40°C to 85°C
ï§ Operating Humidity
10% to 90% relative humidity, noncondensing
ï§ Operating Pressure
105 to 69 kPa (up to 10000 ft.)
ï§ Storage Temperature
-55°C to 100°C
ï§ Storage Humidity
5% to 95% relative humidity, noncondensing
ï§ Storage Pressure
1682 PSI (up to 5000 ft.) at 50°C
Features:
ï§ 200-pin 64-bit Small Outline, Dual-In-Line Double
Data Rate Synchronous DRAM Module
ï§ Module organization: single rank 128M x 64
ï§ VDD = 1.8V ±0.1V, VDDQ 1.8V ±0.1V
ï§ 1.8V I/O ( SSTL_18 compatible)
ï§ Auto Refresh (CBR) and Self Refresh 8k Refresh
every 64ms
ï§ Serial Presence Detect with EEPROM
ï§ Gold-contact pad
ï§ This module is fully pin and functional compatible to
the JEDEC PC2-6400 spec. and JEDEC- Standard
MO-224. (see www.jedec.org)
ï§ The pcb and all components are manufactured
according to the RoHS compliance specification
[EU Directive 2002/95/EC Restriction of Hazardous
Substances (RoHS)]
ï§ DDR2 - SDRAM component SAMSUNG
K4T1G084QF DIE Rev. F
ï§ 128Mx8 DDR2 SDRAM in FBGA-60 package
ï§ Four bit prefetch architecture
ï§ DLL to align DQ and DQS transitions with CK
ï§ Eight internal device banks for concurrent operation
ï§ Programmable CAS latency (CL)
ï§ Posted CAS additive latency (AL)
ï§ WRITE latency = READ latency â 1 tCK
ï§ Programmable burst length: 4 or 8
ï§ Adjustable data-output drive strength
ï§ On-die termination (ODT)
Figure: mechanical dimensions1
Swissbit AG
Industriestrasse 4
Ch-9552 Bronschhofen
1if no tolerances specified ± 0.15mm
Fon: +41 (0) 71 913 03 03
Fax: +41 (0) 71 913 03 15
www.swissbit.com
eMail: info@swissbit.com
Page 1
of 14
|
▷ |