PD5019 Datasheet, PDF (2/14 Pages) List of Unclassifed Manufacturers – Telephone Ring Generator Controller

FEATURES
♦ Integrated Overload and Short Circuit Protection
♦ Programmable Large Swing Output Amplitude
♦ Digitally Selectable Ringing Frequencies; 16.7/20/25 or 50Hz
♦ Line Regulated Output Amplitude, 45-93Vrms
♦ Overload Protection with Adaptive Output Amplitude
♦ High Output Load Indication Signal
♦ Zero Crossing Synchronization Output
♦ Operates from a Single 5V Supply
♦ Open Loop Flyback Topology Reduces Component Count
♦ Total Bill of Material Cost as Low as $5 Including the PD5019
for 2W Ring Generator Applications
♦ 90 Days Warranty
APPLICATIONS
♦ 1 to 3 Watt Low Cost Sine Wave Ring Generators
♦ 3 to 6 Watt advanced Sine Wave Ring Generators
♦ Large Variety of Customized Sine Wave Ring Generators
♦ Ring Generator for PBX, PABX, DCL, CTI and Key Systems
♦ Ring Generator for Rural Telephony and Wireless Local Loop Systems
♦ Ring Generator for Integrated Access Devices
♦ Ring Generator for VoIP Gateways
♦ Ring Generator for Short/Long Loop Applications
♦ Ring Generator for Telecom Test Equipment
PD5019
TELEPHONE RING GENERATOR CONTROLLER
INHIBIT
1
FS
2
F1
3
F0
4
OHD
5
XTAL1
6
XTAL2
7
GND
8
16
Vcc
15
PWM_Out
14
WDO
13
CL
12
CAD_In
11
PAD_Out
10
BRC
9
SYNC
SOW-16 Package
GENERAL DESCRIPTION
The PD5019 is a unique pulse width modulator controller, designed primarily for a variety of high voltage sinusoidal telephone ring generator
applications. The PD5019 is suitable for applications requiring up to 6 Watt and provides all necessary controls for implementing advanced
overload protection, zero crossing relay switching synchronization, Off-Hook detection, multiple ringing frequency selection and output
amplitude adjustment.
The power train, designed to be used with the PD5019, is an isolated, open loop flyback topology. The PD5019 generates a PWM signal,
which drives a FET transistor that switches the primary of a flyback transformer. This produces a rectified half sine wave on the secondary
side of the transformer. An additional control signal synchronizes a 4-output transistor bridge, which converts the rectified half sine wave to full
sine wave. In order to maintain the ring generator’s input to output isolation, the synchronization signals control the bridge via an opto coupler
pair. The controller also includes overload protection, A/D function for measuring the input voltage, and a report signal for indicating over
current.
The PD5019 is a cost-effective solution for applications using more than 10,000 units. For quantities less than 10,000 units, the most
economical solution is a modular sine wave ring generator (PCR-SIN01A Series or the PCR-SIN06 Series).
INTERNAL BLOCK DIAGRAM
PD5019
CL
OHD
Vcc
Over-Current
Sensing
Mechanism
Overload
Protection
GND
CAD_In
PAD_Out
Vin
Sense
A/D
Transfer Function
PWM
Unit
PWM_Out
XTAL1
XTAL2
FS
INHIBIT
F0
F1
BRC
SYNC
Clock
Circuitry
Reset
Clock
Sine
Generator
PowerDsine Ltd.
PowerDsine, Inc.
PowerDsine Europe
Tel: [phone] • Fax: [phone] • Email: [e-mail]
Tel: [phone] • Fax: [phone] • Email: [e-mail]
Tel: [phone] • Fax: [phone] • Email: [e-mail]