N04L163WC1C Datasheet, PDF (3/10 Pages) List of Unclassifed Manufacturers – 4Mb Ultra-Low Power Asynchronous CMOS SRAM

NanoAmp Solutions, Inc.
N04L163WC1C
Advance Information
Absolute Maximum Ratings¹
Item
Symbol
Rating
Unit
Voltage on any pin relative to V_SS
V_IN,OUT
–0.3 to V_CC+0.3
V
Voltage on V_CC Supply Relative to V_SS
V_CC
–0.3 to 4.5
V
Power Dissipation
P_D
500
mW
Storage Temperature
T_STG
–65 to 150
o_C
Operating Temperature
T_A
-40 to +85
o_C
Soldering Temperature and Time
T_SOLDER
260^oC, 10sec
o_C
1. Stresses greater than those listed above may cause permanent damage to the device. This is a stress rating only and functional
operation of the device at these or any other conditions above those indicated in the operating section of this specification is not
implied. Exposure to absolute maximum rating conditions for extended periods may affect reliability.
Operating Characteristics (Over Specified Temperature Range)
Item
Symbol
Test Conditions
Min. _Typ¹ Max Unit
Supply Voltage
V_CC
2.2 3.0 3.6 V
Data Retention Voltage
V_DR
Chip Disabled
1.5
V
Input High Voltage
V_IH
Vcc = 2.2V to 2.7V
Vcc = 2.7V to 3.6V
1.8
V_CC+0.3
V
2.2
V_CC+0.3
Input Low Voltage
Vcc = 2.2V to 2.7V
-0.3
0.6
V_IL
Vcc = 2.7V to 3.6V
-0.3
V
0.8
Output High Voltage
V_OH
I_OH = -0.1mA, Vcc = 2.20V
I_OH = -1.0mA, Vcc = 2.70V
2.0
2.4
V
Output Low Voltage
V_OL
I_OL = 0.1mA, Vcc = 2.20V
I_OL = 2.1mA, Vcc = 2.70V
0.4
V
0.4
Input Leakage Current
I_LI
V_IN = 0 to V_CC
-1
1 µA
Output Leakage Current
I_LO
OE = V_IH or Chip Disabled
V_OUT = 0 to V_CC
-1
1 µA
Read/Write Operating Supply Current
@ 1 µs Cycle Time²
I_CC1
V_CC=3.6 V, V_IN=V_IH or V_IL
Chip Enabled, I_OUT = 0
-L
1.5 3.0
mA
1.5 3.0
Read/Write Operating Supply Current
@ fmax
I_CC2
V_CC=3.6 V, V_IN=V_IH or V_IL
Chip Enabled, I_OUT = 0
-L
8 15.0
mA
8 10.0
Maximum Standby Current
V_IN = V_CC or 0V
I_SB1
Chip Disabled
t_A= 85^oC, VCC = 3.6 V
-L
2.0 12
µA
2.0
8
Maximum Data Retention Current
I_DR
Vcc = 1.5V, CE ≥ Vcc - 0.2V,
VIN ≥ Vcc - 0.2V or VIN ≤ 0.2V _-L
9
µA
6
1. Typical values are measured at Vcc=Vcc Typ., T_A=25°C and are not 100% tested.
2. This parameter is specified with the outputs disabled to avoid external loading effects. The user must add current required to drive
output capacitance expected in the actual system.
Stock No. 23373-C 1/05
3
The specifications of this device are subject to change without notice. For latest documentation see http://www.nanoamp.com.