VMX1C1016 Datasheet, PDF (1/76 Pages) List of Unclassifed Manufacturers – Versa Mix 8051 Mixed-Signal MCU

VMX1C1016
Datasheet
Rev 1.0
Versa Mix 8051 Mixed-Signal MCU
Overview
The VMX51C1016 is a fully integrated mixed-signal
microcontroller that provides a “one-chip” solution for
a broad range of control, data acquisition and
processing applications. The VXM1016 is based on a
powerful, single-cycle, RISC-based 8051 processor
with an enhanced MULT/ACCU unit that can be used
to perform complex mathematical operations. The
device includes 56KB of Flash memory and 1280
bytes of RAM.
On-chip analog peripherals such as: an A/D
converter, PWM outputs (that can be used as D/A
converters), a voltage reference and an analog switch
make the VMX51C1020 ideal for analog data
acquisition applications.
The inclusion of a full set of digital interfaces such as
an enhanced, fully configurable SPI, an I²C, UARTs
and a J1708/RS-485 compatible differential
transceiver, enables total system integration.
The VMX51C1016 operates on a 5 volt supply and is
available in a QFP-44 package.
Applications
o Automotive Applications
o Industrial Controls / Instrumentation
o Consumer Products
o Medical Devices
FIGURE 1: VMX51C1016 BLOCK DIAGRAM
8051
µPROCESSOR
SINGLE CYCLE
1 2 -BIT A/D
CONVERTER
XTVREF Input
ADCITA connected to A /D Input
Multiplexer
Band gap
Reference
PGA
4 P4W4PM4WPOWPMuWMtDpMDu/AtD/ssA/sA s
8 / 16 bit Resolution
(Can be used as D /A s )
XTAL
1 DIGITALLY
CONTROLLED
SWITCH
J 1708 /RS 485
Compatible
Transceiver
Clock Control Unit
In -Circuit
Debugging
through UART0
2 UARTs
Serial Ports
56KB
Program FLASH
(In -Circuit Programmable )
1280 Bytes RAM
(256 x8 & 1kX8)
· 24 I/O s
· 1 I n t. input
· Int. Port1
change
· 3 Timers ,
· 2 Baud Rate
Generators
· 2 CCU inputs
[M U L T / A C C U ]
Unit with
BARREL
SHIFTER
SPI Interface
I²C Bus
Interface
Power On Reset
Circuit
+
WatchDog Timer
Feature Set
o 8051 Compatible RISC Performance Processor
Enhanced Arithmetic Unit including Barrel Shifter
o 56KB of Flash Memory
o 1280 Bytes of RAM
o 24 General Purpose I/Os
o 2 UART Serial Ports
o 2 Baud Rate Generators for UARTs
o Diff. Transceiver connected to UART1
J1708/RS-485 compatible)
o Enhanced SPI interface (Master/Slave)
o Fully configurable
o Control up to 4 Slave devices
o I²C interface
o 1 External Dedicated Interrupt Input
o Interrupt on Port 1.0-P1.3 Pin Change
o 3, 16-bit Timers/Counters
o 4 Compare Units and 2 Capture Inputs
o 4 Ch. PWM, 8-bit / 16-bit resolution
o 5 Ch. 12-bit A/D Converter
o Conversion rate configurable up to
10KHz
o Continuous/One-Shot Operation
o Single or 4-Channel Automatic
Sequential Conversions
o On-Chip Voltage Reference
o Digitally Controlled Switch
o Power Saving Features + Clock Control
o Watchdog Timer
o Operating Temperature range (0ºC to +70ºC)
o Available in QFP-44 package
FIGURE 2: VMX51C1016-QAC14, QFP-44 PACKAGE PINOUT
INT0
PM
RES-
ADCITA
VDDA
ADCI3
ADCI2
ADCI1
ADCI0
XTVREF
AGND
33
34
23
22
VMX51C1016
QFP-44
44
12
1
11
VDD
P2.7-SDI
P2.6-SDO
P2.5-SCK
P2.4-SS-
P2.3-CS0-
P2.2-CS1-
P2.1-CS2-
P2.0-CS3-
DGND
P1.3-PWM3
Table 1: Pinout description
Ramtron International Corporation ? http://www.ramtron.com
1850 Ramtron Drive Colorado Springs ? MCU customer service: 1-800-943-4625, 1-514-871-2447, ext. 208
Colorado, USA, 80921 ? 1-800-545-FRAM, 1-719-481-7000
page 1of 76