EN29GL128H_10 Datasheet, PDF (54/54 Pages) Eon Silicon Solution Inc. – 128 Megabit (16384K x 8-bit / 8192K x 16-bit) Flash Memory Page mode Flash Memory, CMOS 3.0 Volt-only

Revisions List
EN29GL128H/L
Revision No
A
B
C
D
E
F
G
H
I
J
K
Description
Date
Preliminary
2009/01/23
1.Add Sector for write protect selection in Ordering information
2.Modify PPB sector group in table 7 and Figure 7.
2009/02/18
3. Modify sector erase descirption and Figure 6.
1. Add internal pull-up description for WP# pin in Table1 on Page 4
2. Add WP#/ACC, VIO pin in Figure3 on Page 4
3. Modify tOE from 30ns to 25ns in Table 17 on Page 40 and Page 5
4. Add Secured Silicon Sector Entry/Exit command in Table13
5. Modify typo from Sector Erase Suspend to Erase/Program Suspend,
from Sector Erase Resume to Erase/Program resume in Table13
6. Modify package code for 56-pin TSOP from T to Z in ordering
information on Page 54
7. Del table 22 and Figure 20 Temporary Sector Unprotect Timing table
and Diagram and Figure 21.Sector Protect/Unprotect Timing Diagram
8. Modify Erase/Program performance in Table 20, 21 and 22.
Chip erase time from 32Æ30sec typ and 280Æ120sec max.
Add ACC and total write buffer time spec
9. Correct typo from Byte to Word on Page 7
2009/05/12
10. Del t_CEH in table 17
11. Modify DC Characteristics in table 15
VHH from 10.5~11.5V to 8.5~9.5V
ICC1 5MHz 9Æ15mA typ, 10MHz 16Æ25mA typ
ICC4, ICC5 and ICC6 1Æ1.5uA typ, 5Æ10uA max
Add IIO2 and IACCspec
12. Del apply VID on address pin A9 to access autoselect codes
function. ( Remove TABLE 5 and modify description Autoselect
section for using High voltage to get Autoselect Codes )
13. Modify A9 spec from 9.5V to Vcc+0.5V in ABSOLUTE MAXIMUM
RATINGS
14. Modify CFI 4Ah, 4Fh description and data of 4Fh in table 12
1. Modify naming for DQ0 OTP Lock Bit to Secured Silicon Sector
Protection Bit on Page 25
2. Modify Table.8 Secured Silicon Sector Address Range 000000h-
000007h from Determined by customer to Reserve for Factory
2009/06/19
3. Add note “The address 0h~7h in Secured Silicon Sector is reserved
for Factory“ on Page 31
Update FIGURE 23. 64
mm, Pitch 1mm package
ball Fortified Ball Grid
outline on page 52
Array
(FBGA),
11
X13
2009/07/01
1. Modify from Sector 0 to all sectors in note 1 of Table 6 and note 2, 3
and note 9
2. Add “User
of PPB section on page 25.
only can use DQ6 and RY/BY#
pin
to
detect
programming
2009/07/14
status” in note 10 on page26.
Change the package code of 64-ball BGA on page 53.
2009/07/22
Correct typo in Table 20, “ tB_BUSY “ from Min. to Max on page 42. ^2009/10/01
Add a note "when sector SA0 is suspended, if system enters Secured
Sector mode,." on page 29.
2009/11/02
Add Write Buffer byte mode command and note that maximum value is
31 for word and byte mode in page 34
2010/02/10
1. Update Table 15. DC Characteristics on page 36.
(1) Icc3 from 30mA to 40mA. (max.)
2010/05/11
(2) Icc4, Icc5, Icc6 from 1.5/10uA to 2.0/20uA (typ./max.)
This Data Sheet may be revised by subsequent versions
54
or modifications due to changes in technical specifications.
©2004 Eon Silicon Solution, Inc.,
Rev. K, Issue Date: 2010/05/11
www.eonssi.com