|
DA14582 Datasheet, PDF (1/177 Pages) Dialog Semiconductor – Low Power Bluetooth Smart SoC with Audio Codec | |||
|
DATASHEET - PRELIMINARY
MARCH 11, 2015 V2.0
DA14582
Low Power Bluetooth Smart SoC with Audio Codec
General description
ï® 16 MHz 32 bit ARM Cortex-M0 with SWD I/F
The DA14582 integrated circuit has a fully integrated
radio transceiver, baseband processor for Bluetooth®
Smart with Audio Codec.
ï® Dedicated Link Layer Processor
ï® AES-128 bit encryption Processor
ï® Memories
ï® 32 kB One-Time-Programmable (OTP) memory
The DA14582 is optimized for remote control units
ï® 42 kB System SRAM
(RCU) requiring support for voice commands and
ï® 84 kB ROM
motion/gesture recognition. Its integrated analog wide
ï® 8 kB Retention SRAM
band audio codec provides native support for analog ï® Power management
microphones thereby reducing the total number of
ï® Integrated Buck DC-DC converter
components of the system while its optimized package
ï® P0, P1, P2 and P3 ports with 3.3 V tolerance
enables designs using single-layer FR1 PCBs further-
ï® Easy decoupling of only 4 supply pins
more contributing to the reduction of the cost of the
ï® Supports coin (typ. 3.0 V) and alkaline (typ. 1.5 V)
system.
battery cells
The DA14582 supports a flexible memory architecture
for storing Bluetooth profiles and custom application
code, which can be updated over the air (OTA). The
qualified Bluetooth Smart protocol stack is stored in a
dedicated ROM. All software runs on the ARM® Cor-
tex®-M0 processor via a simple scheduler.
ï® 10-bit ADC for battery voltage measurement
ï® Digital controlled oscillators
ï® 16 MHz crystal (±20 ppm max) and RC oscillator
ï® 32 kHz crystal (±50 ppm, ±500 ppm max) and
RCX oscillator
ï® General purpose, Capture and Sleep timers
ï® Digital interfaces
The Bluetooth Smart firmware includes the L2CAP ser-
ï® 29 General purpose I/Os
vice layer protocols, Security Manager (SM), Attribute
ï® 2 UARTs with hardware flow control up to 1 MBd
Protocol (ATT), the Generic Attribute Profile (GATT)
ï® SPI+⢠interface
and the Generic Access Profile (GAP). All profiles pub-
ï® I2C bus at 100 kHz, 400 kHz
lished by the Bluetooth SIG as well as custom profiles
ï® 3-axis capable Quadrature Decoder
are supported.
ï® Analog interfaces
The transceiver interfaces directly to the antenna and
is fully compliant with the Bluetooth 4.1 standard.
ï® 4-channel 10-bit ADC
ï® 14 bits wide band Codec with microphone and
28 ï loudspeaker analog front-end
The DA14582 has dedicated hardware for the Link
Layer implementation of Bluetooth®Smart and inter-
ï® Radio transceiver
ï® Fully integrated 2.4 GHz CMOS transceiver
face controllers for enhanced connectivity capabilities.
ï® Single wire antenna: no RF matching or RX/TX
Features
switching required
ï® Supply current at VBAT3V:
ï® Complies with Bluetooth V4.1, ETSI EN 300 328 and
EN 300 440 Class 2 (Europe), FCC CFR47 Part 15
(US) and ARIB STD-T66 (Japan)
ï® Processing power
TX: 3.4 mA, RX: 3.7 mA (with ideal DC-DC)
ï® 0 dBm transmit output power
ï® -20 dBm output power in âNear Field Modeâ
ï® -93 dBm receiver sensitivity
________________________________________________________________________________________________
System diagram
© 2015 Dialog Semiconductor
1
www.dialog-semiconductor.com
|
▷ |