CYRF69103_08 Datasheet, PDF (57/65 Pages) Cypress Semiconductor – Programmable Radio on Chip Low Power

CYRF69103
DC Characteristics (T = 25°C) (continued)
Parameter
Description
Radio Function Currents (V_CC = 3.0V, MCU Sleep)
IDLE I_CC
Radio off, XTAL Active
I_synth
I_CC during Synth Start
TX I_CC
I_CC during Transmit
TX I_CC
I_CC during Transmit
TX I_CC
I_CC during Transmit
RX I_CC
I_CC during Receive
RX I_CC
I_CC during Receive
Boost Eff
PMU Boost Converter Efficiency
I_{LOAD_EXT}
Average PMU External Load current
MCU Function Currents (V_DD = 3.0V)
I_DD1
V_DD Operating Supply Current
I_DD1
V_DD Operating Supply Current
Radio Function GPIO Interface
V_OH1
Output High Voltage Condition 1
V_OH2
Output High Voltage Condition 2
V_OL
Output Low Voltage
V_IH
Input High Voltage
V_IL
Input Low Voltage
I_IL
Input Leakage Current
C_IN
Pin Input Capacitance
MCU Function GPIO Interface
R_UP
V_ICR
Pull-up Resistance
Input Threshold Voltage Low, CMOS
mode
V_ICF
Input Threshold Voltage Low, CMOS
mode
V_HC
V_ILTTL
V_IHTTL
V_OL1
V_OL2
V_OL3
V_OH
Input Hysteresis Voltage, CMOS Mode
Input Low Voltage, TTL Mode
Input HIGH Voltage, TTL Mode
Output Low Voltage, High Drive^[15]
Output Low Voltage, High Drive^[15]
Output Low Voltage, Low Drive
Output High Voltage^[16]
Conditions
XOUT disabled
PA = 5 (–5 dBm)
PA = 6 (0 dBm)
PA = 7 (+4 dBm)
LNA off, ATT on.
LNA on, ATT off.
V_BAT = 2.5V,
V_REG = 2.73V, I_LOAD = 20 mA
V_BAT = 1.8V,
V_REG = 2.73V, RX Mode
CPU speed = 6 MHz
CPU speed = 3 MHz
At I_OH = –100.0 µA
At I_OH = –2.0 mA
At I_OL = 2.0 mA
0 < V_IN < V_IO
except XTAL, RF_N, RF_P, RF_BIAS
Low to High edge
High to Low edge
High to low edge
I_OL1 = 50 mA
I_OL1 = 25 mA
I_OL2 = 8 mA
I_OH = 2 mA
Min Typ Max Unit
1.1
mA
8.6
mA
21.2
mA
28.5
mA
39.9
mA
18.9
mA
21.9
mA
83
%
15 mA
5.0
mA
4.4
mA
V_IO – 0.1 V_IO
V
V_IO – 0.4 V_IO
V
0
0.4
V
0.76V_IO
V_IO
V
0
0.24V_IO V
–1 0.26 +1 µA
3.5 10 pF
4
40%
30%
3%
1.6
V_CC – 0.5
12 KΩ
65% V_CC
55% V_CC
10% V_CC
0.72 V
V
1.4 V
0.4 V
0.8 V
V
Notes
15. Available only on P1.3,P1.4,P1.5,P1.6,P1.7.
16. Except for pins P1.0, P1,1 in GPIO mode.
Document #: 001-07611 Rev *C
Page 57 of 65
[+] Feedback