W181-01GT Datasheet, PDF (5/9 Pages) Cypress Semiconductor – Peak-Reducing EMI Solution

W181
.
Absolute Maximum Conditions^[2]
Parameter
V_DD, V_IN
T_STG
T_A
T_B
P_D
Description
Voltage on any pin with respect to GND
Storage Temperature
Operating Temperature
Ambient Temperature under Bias
Power Dissipation
Rating
Unit
–0.5 to +7.0
V
–65 to +150
°C
0 to +70
°C
–55 to +125
°C
0.5
W
DC Electrical Characteristics: 0°C < T_A < 70°C, V_DD = 3.3V ±5%
Parameter
Description
Test Condition
I_DD
Supply Current
t_ON
Power-Up Time
First locked clock cycle after Power
Good
V_IL
V_IH
V_OL
V_OH
I_IL
I_IH
I_OL
I_OH
C_I
C_I
R_P
Z_OUT
Input Low Voltage
Input High Voltage
Output Low Voltage
Output High Voltage
Input Low Current
Input High Current
Output Low Current
Output High Current
Input Capacitance
Input Capacitance
Input Pull-Up Resistor^[3]
Clock Output Impedance
Note 3
Note 3
@ 0.4V, V_DD = 3.3V
@ 2.4V, V_DD = 3.3V
All pins except CLKIN
CLKIN pin only
Min.
–
–
–
2.4
–
2.4
–
–
–
–
–
–
–
–
Typ.
18
–
–
–
–
–
–
–
15
15
v
6
500
25
Max.
Unit
32
mA
5
ms
0.8
V
–
V
0.4
V
–
V
–100
µA
10
µA
–
mA
–
mA
7
pF
10
pF
–
kΩ
–
Ω
DC Electrical Characteristics: 0°C < T_A < 70°C, V_DD = 5V ±10%
Parameter
Description
Test Condition
Min.
Typ.
Max.
Unit
I_DD
Supply Current
t_ON
Power-Up Time
First locked clock cycle after
Power Good
30
50
mA
5
ms
V_IL
Input Low Voltage
0.15V_DD
V
V_IH
Input High Voltage
0.7V_DD
V
V_OL
Output Low Voltage
0.4
V
V_OH
Output High Voltage
2.4
V
I_IL
Input Low Current
Note 3
–100
µA
I_IH
Input High Current
Note 3
10
µA
I_OL
Output Low Current
@ 0.4V, V_DD = 5V
24
mA
I_OH
Output High Current
@ 2.4V, V_DD = 5V
24
mA
C_I
Input Capacitance
All pins except CLKIN
7
pF
C_I
Input Capacitance
CLKIN pin only
6
10
pF
R_P
Input Pull-Up Resistor
500
kΩ
Notes:
1. Stresses greater than those listed in this table may cause permanent damage to the device. These represent a stress rating only. Operation of the device at
these or any other conditions above those specified in the operating sections of this specification is not implied. Maximum conditions for extended periods may
affect reliability
2. Single Power Supply: The voltage on any input or I/O pin cannot exceed the power pin during power-up.
3. Inputs FS1:2 have a pull-up resistor; Input SSON# has a pull-down resistor.
Document #: 38-07152 Rev. *D
Page 5 of 9