CPC7582 Datasheet, PDF (2/12 Pages) Clare, Inc. – Line Card Access Switch

CPC7582
Absolute Maximum Ratings (@ 25˚ C)
Parameter
Min
Operating Temperature Range
-40
Storage Temperature Range
-40
Relative Humidity Range
5
Pin Soldering Temperature
-
(t=10 s max)
+5V Power Supply
-
Battery Supply
-
Logic Input Voltage
-
Logic Input to Switch Output Isolation -
Switch Isolation (SW1, SW2, SW3, SW5, SW6) -
Switch Isolation (SW4)
-
Max
+110
+150
95
+260
Units
˚C
˚C
%
˚C
7
V
-85 V
7
V
330 V
330 V
480 V
Electrical Characteristics TA = -40^oC to +85^oC
(unless otherwise specified)
Minimum and maximum values are production testing
requirements. Typical values are characteristic of the
device and are the result of engineering evaluations.
Typical values are provided for information purposes
only and are not part of the testing requirements.
Absolute Maximum Ratings are stress ratings. Stresses in
excess of these ratings can cause permanent damage to
the device. Functional operation of the device at these or
any other conditions beyond those indicated in the opera-
tional sections of this data sheet is not implied. Exposure of
the device to the absolute maximum ratings for an extend-
ed period may degrade the device and effect its reliability.
Power Supply Specifications
Supply
Min Typ Max Unit
V_DD
V_BAT1
+4.5 +5.0 +5.5
V
-19
-
-72
V
1 _{VBAT is used only as a reference for internal protection circuitry.}
If V_BAT rises above -10V, the device will enter an all off state and will remain in the all off state
until the battery voltage drops below -15V.
ESD Rating (HBM)
1000V
Table 1. Break Switch, SW1 and SW2
Parameters
Conditions
Off-state Leakage Current:
+25˚C
+85˚C
-40˚C
RDS_ON (SW1,SW2):
+25˚C
+85˚C
-40˚C
RDS_ON Match
dc Current Limit:
+25˚C
+85˚C
-40˚C
Dynamic Current Limit:
(t=<0.5µs)
Vsw (differential)= -320V to Gnd
Vsw (differential)= -60V to +260V
Vsw (differential)= -330V to Gnd
Vsw (differential)= -60V to +270V
Vsw (differential)= -310V to Gnd
Vsw (differential)= -60V to +250V
T_LINE= +/-10 mA, +/-40mA, T_BAT= -2V
T_LINE= +/-10 mA, +/-40mA, T_BAT= -2V
T_LINE= +/-10 mA, +/-40mA, T_BAT= -2V
Per ON-resistance Test Condition of
SW1, SW2R_ON SW1-R_ONSW2
V_sw (on) = +/- 10V
V_sw (on) = +/- 10V
V_sw (on) = +/- 10V
Break switches in ON state, Ringing
access switches OFF, Apply +/- 1000V
at 10/1000ms pulse, Appropriate
secondary protection in place.
Symbol
Isw
Isw
Isw
∆V
∆V
∆V
Magnitude
lsw
lsw
lsw
Isw
Min
Typ
Max
-
0.1
1
-
0.3
1
-
0.1
1
-
14.5
-
-
20.5
28
-
10.5
-
-
0.15
0.8
-
300
-
80
160
-
-
400
425
-
2.5
-
Units
µA
µA
µA
Ω
Ω
Ω
Ω
mA
mA
mA
A
2
www.clare.com
Rev. 1.0