CAT24WC164_1 Datasheet, PDF (2/13 Pages) Catalyst Semiconductor – 16K-Bit Serial EEPROM, Cascadable

CAT24WC164
ABSOLUTE MAXIMUM RATINGS*
*COMMENT
Temperature Under Bias ................. –55°C to +125°C Stresses above those listed under “Absolute Maximum
Storage Temperature ....................... –65°C to +150°C
Voltage on Any Pin with
Respect to Ground⁽¹⁾ ........... –2.0V to +V_CC + 2.0V
VCC with Respect to Ground ............... –2.0V to +7.0V
Ratings” may cause permanent damage to the device.
These are stress ratings only, and functional operation of
the device at these or any other conditions outside of those
listed in the operational sections of this specification is not
implied. Exposure to any absolute maximum rating for
Package Power Dissipation
extended periods may affect device performance and
Capability (Ta = 25°C) ................................... 1.0W reliability.
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current⁽²⁾ ........................ 100mA
t _{RELIABILITY CHARACTERISTICS}
r _Symbol
Parameter
N_END(3)
a _TDR(3)
P ^VZAP(3)
I_LTH(3)(4)
Endurance
Data Retention
ESD Susceptibility
Latch-up
Min.
1,000,000
100
2000
100
Max.
Units
Cycles/Byte
Years
Volts
mA
d _{D.C. OPERATING CHARACTERISTICS}
e V_CC = +1.8V to +5.5V, unless otherwise specified.
Symbol Parameter
Test Conditions
Min
Typ
Max Units
u _ICC
tin ^ISB(5)
Power Supply Current
Standby Current (V_CC = 5.0V)
f_SCL = 100 kHz
V_IN = GND or V_CC
3
mA
1
µA
I_LI
Input Leakage Current
V_IN = GND to V_CC
10
µA
I_LO
Output Leakage Current
V_OUT = GND to V_CC
10
µA
n ^VIL
Input Low Voltage
–1
VCC x 0.3 V
VIH
Input High Voltage
VCC x 0.7
VCC + 0.5 V
o _{VOL1 Output Low Voltage (VCC = 3.0V)}
I_OL = 3 mA
0.4
V
c ^{VOL2 Output Low Voltage (VCC = 1.8V)}
I_OL = 1.5 mA
0.5
V
is ^{CAPACITANCE TA = 25°C, f = 1.0 MHz, VCC = 5V}
Symbol Parameter
Test Conditions
Min
D^{CI/O(3) Input/Output Capacitance (SDA)}
V_I/O = 0V
Typ
Max Units
8
pF
C_IN(3) Input Capacitance
V_IN = 0V
6
pF
(A0, A1, A2, SCL, WP)
Note:
(1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is V_CC +0.5V, which may overshoot to V_CC + 2.0V for periods of less than 20ns.
(2) Output shorted for no more than one second. No more than one output shorted at a time.
(3) These parameter are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100
and JEDEC test methods.
(4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to V_CC +1V.
(5) Maximum standby current (I_SB ) = 10µA for the Automotive and Extended Automotive temperature range.
Doc. No. 1026, Rev. J
2