CAT24FC64_05 Datasheet, PDF (2/10 Pages) Catalyst Semiconductor – 64K-Bit I2C Serial CMOS EEPROM

CAT24FC64
ABSOLUTE MAXIMUM RATINGS*
Package Power Dissipation
Temperature Under Bias ................. –55°C to +125°C
Storage Temperature ....................... –65°C to +150°C
Voltage on Any Pin with
Respect to Ground⁽¹⁾ ........... –2.0V to +V_CC + 2.0V
Capability (Ta = 25°C) ................................... 1.0W
Lead Soldering Temperature (10 secs) ............ 300°C
Output Short Circuit Current⁽²⁾ ........................ 100mA
*COMMENT
V_CC with Respect to Ground ............... –2.0V to +7.0V
Stresses above those listed under “Absolute Maximum Ratings” may
cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions
outside of those listed in the operational sections of this specification is not
RELIABILITY CHARACTERISTICS ⁽³⁾
Symbol
Parameter
t _NEND
Endurance
r _TDR
Data Retention
a ^VZAP
ILTH(4)
ESD Susceptibility
Latch-up
implied. Exposure to any absolute maximum rating for extended periods
may affect device performance and reliability.
Min
Typ
1,000,000
100
4000
100
Max
Units
Cycles/Byte
Years
Volts
mA
P _{D.C. OPERATING CHARACTERISTICS}
V_CC = +2.5V to +5.5V, unless otherwise specified.
d _{Symbol Parameter}
Test Conditions Min
Typ
Max Units
I_CC1
ue ^ICC2
tin ^ISB(5)
I_LI
I_LO
n _VIL
o ^VIH
V_OL
Power Supply Current - Read
Power Supply Current - Write
Standby Current
Input Leakage Current
Output Leakage Current
Input Low Voltage
f_SCL = 400 KHz
V_CC=5V
f_SCL = 400KHz
V_CC=5V
V_IN = GND or V_CC
V_CC=5V
V_IN = GND to V_CC
V_OUT = GND to V_CC
-0.5
Input High Voltage
Output Low Voltage (V_CC = +3.0V)
I_OL = 3.0 mA
V_CC x 0.7
1
mA
3
mA
1
µA
1
µA
1
µA
V_CC x 0.3 V
V_CC + 0.5 V
0.4
V
c _{CAPACITANCE TA = 25°C, f = 1.0 MHz, VCC = 5V}
is ^{Symbol Test}
Conditions Min
Typ
C_I/O(3) Input/Output Capacitance (SDA)
V_I/O = 0V
DCIN(3)
Input Capacitance (SCL, WP, A0, A1)
V_IN = 0V
Max
Units
8
pF
6
pF
Z_WPL
WP Input Impedance
V_IN ≤ 0.5V
5
70
kΩ
Z_WPH
WP Input Impedance
V_IN>0.7VxV_CC 500
kΩ
Note:
(1) The minimum DC input voltage is –0.5V. During transitions, inputs may undershoot to –2.0V for periods of less than 20 ns. Maximum DC
voltage on output pins is V_CC +0.5V, which may overshoot to V_CC + 2.0V for periods of less than 20ns.
(2) Output shorted for no more than one second. No more than one output shorted at a time.
(3) These parametesr are tested initially and after a design or process change that affects the parameter according to appropriate AEC-Q100
and JEDEC test methods.
(4) Latch-up protection is provided for stresses up to 100 mA on address and data pins from –1V to V_CC +1V.
(5) Maximum standby current (I_SB) = 10µA for the Extended Automotive temperature range.
Doc. No. 1046, Rev. K
2
© 2005 by Catalyst Semiconductor, Inc.
Characteristics subject to change without notice