PACVGA201 Datasheet, PDF (2/3 Pages) California Micro Devices Corp – VGA PORT COMPANION CIRCUIT

CALIFORNIA MICRO DEVICES
PACVGA201
ABSOLUTE MAXIMUM RATINGS
Parameter
Rating
V_CC1, V_CC3 supply voltage
DC voltage at inputs:
GND-0.5, +6.0
VIDEO_1, VIDEO_2, VIDEO_3
DDC_OUT1, DDC_OUT2
SYNC_IN1, SYNC_IN2
Temperature:
GND-0.5, V_CC1+0.5
GND-0.5, V_CC2+0.5
GND-0.5, V_CC3+0.5
Storage
-40 to +150
Operating Ambient
0 to +70
Package power dissipation
0.75
Unit
V
V
V
V
V
o_C
o_C
W
Symbol
I_CC1
I_CC3
V_CC2
V _IH
V _IL
V _OH
V_OL
R_b, R_p
I_N
C_IN
t_PLH
t_PHL
t_r, t_f
V_ESD
ELECTRICAL OPERATING CHARACTERISTICS
(over operating conditions unless specified otherwise)
Parameter
Conditions
MIN
V_CC1 supply current
V_CC3 supply current
V_CC1 = 5V
V_CC3 = 5V; SYNC inputs at GND or V_CC3;
PWR_UP pin at V_CC3; SYNC outputs unloaded
V_CC3 = 5V; SYNC inputs at 3.0V; PWR_UP
pin at V_CC3; SYNC outputs unloaded
V_CC3 = 5V; PWR_UP input at GND; SYNC
outputs unloaded
V_CC2 pin open circuit voltage
V_CC2 voltage internally derived from V_CC3 via
diode D1; no external current drawn;
Logic High input voltage¹
V_CC3 = 5.0V
2.0
Logic Low input voltage¹
V_CC3 = 5.0V
Logic High output voltage²
I_OH = -4mA, V_CC3 = 5.0V
4.4
Logic Low output voltage²
I_OL = 4mA, V_CC3 = 5.0V
Resistor value
PWR_UP, V_CC3 = 5.0V
0.5
Input current
VIDEO inputs
HSYNC, VSYNC inputs
Input capacitance ⁴
V_CC1 = 5V; V_IN = V_CC1 or GND
V_CC3 = 5V; V_IN = V_CC3 or GND
VIDEO_1, VIDEO_2, VIDEO_3
V_CC1 = 5.0V; V_IN = 2.5V; measured at 1MHz
V_CC1 = 2.5V; V_IN = 1.25V; measured at 1MHz
SYNC drivers L-H propagation delay C_L = 50 pF; V_CC3 = 5V; Input t_r and t_f < 5ns
SYNC drivers H-L propagation delay C_L = 50 pF; V_CC3 = 5V; Input t_r and t_f < 5ns
SYNC drivers output rise & fall times C_L = 50 pF; V_CC3 = 5V; Input t_r and t_f < 5ns
ESD withstand voltage^{3, 4}
V_CC1 = V_CC2 = V_CC3 = 5V
±8
TYP
10
200
V_CC3-0.8
1
4.0
4.5
8
8
7
MAX
10
10
0.8
0.4
2
±1
±1
12
12
UNIT
uA
uA
uA
uA
V
V
V
V
V
MΩ
µA
µA
pF
ns
ns
ns
kV
Note 1:
Note 2:
Note 3:
Note 4:
These parameters apply only to SYNC_IN1, SYNC_IN2 and PWR_UP.
These parameters apply only to SYNC_OUT1 and SYNC_OUT2.
Per the IEC-61000-4-2 International ESD Standard, Level 4 contact discharge method. V_CC1, V_CC2 and V_CC3 must be bypassed to GND via
a low impedance ground plane with a 0.2uF or greater, low inductance, chip ceramic capacitor at each supply pin. ESD pulse is applied
between the applicable pins and GND. ESD pulse can be positive or negative with respect to GND. Applicable pins are: VIDEO_1,
VIDEO_2, VIDEO_3, SYNC_OUT1, SD1, SYNC_OUT2, SD2, DDC_OUT1 and DDC_OUT2. All other pins are ESD protected to the
industry standard 2kV per the Human Body model (MIL-STD-883, Method 3015).
This parameter is guaranteed by design and characterization.
©2000 California Micro Devices Corp. All rights reserved.
2
215 Topaz Street, Milpitas, California 95035 Tel: [phone] Fax: [phone] www.calmicro.com
4/00