OPA2686 Datasheet, PDF (2/18 Pages) Burr-Brown (TI) – Dual, Wideband, Low Noise, Voltage Feedback OPERATIONAL AMPLIFIER

SPECIFICATIONS: V_S = ±5V
R_F = 453Ω, R_L = 100Ω, and G =+10, unless otherwise noted. Figure 1 for AC performance.
PARAMETER
CONDITIONS
TYP
+25°C
+25°C⁽²⁾
OPA2686U
GUARANTEED
0°C to –40°C to
70°C ⁽³⁾ +85°C ⁽³⁾
UNITS
MIN/ TEST
MAX LEVEL⁽¹⁾
AC PERFORMANCE (Figure 1)
Closed-Loop Bandwidth
Gain Bandwidth Product (GBP)
Bandwidth for 0.1dB Gain Flatness
Peaking at a Gain of +7
Harmonic Distortion
2nd Harmonic
3rd Harmonic
Two-Tone, 3rd-Order Intercept
Input Voltage Noise
Input Current Noise
Rise/Fall Time
Slew Rate
Settling Time to 0.01%
0.1%
1%
Differential Gain
Differential Phase
Channel-to-Channel Crosstalk
DC PERFORMANCE⁽⁴⁾
Open-Loop Voltage Gain (A_OL)
Input Offset Voltage
Average Offset Voltage Drift
Input Bias Current
Input Bias Current Drift
Input Offset Current
Input Offset Current Drift
INPUT
Common-Mode Input Range (CMIR)⁽⁵⁾
Common-Mode Rejection (CMR)
Input Impedance
Differential-Mode
Common-Mode
OUTPUT
Output Voltage Swing
Current Output, Sourcing
Current Output, Sinking
Closed-Loop Output Impedance
POWER SUPPLY
Specified Operating Voltage
Maximum Operating Voltage
Max Quiescent Current
Min Quiescent Current
Power Supply Rejection Ratio
+PSRR, –PSRR
THERMAL CHARACTERISTICS
Specified Operating Range: U, N Package
Thermal Resistance, θ_JA
U SO-8 Surface Mount
G = +7, R_G = 50Ω, V_O = 200mVp-p
G = +10, R_G = 50Ω, V_O = 200mVp-p
G = +20, R_G = 50Ω, V_O = 200mVp-p
G ≥ +40
G = +10, R_L = 100Ω, V_O = 200mVp-p
G = +10, f = 5MHz, V_O = 2Vp-p
R_L = 100Ω
R_L = 500Ω
R_L = 100Ω
R_L = 500Ω
G = +10, f = 10MHz
f > 1MHz
f > 1MHz
0.2V Step
2V Step
2V Step
2V Step
2V Step
G = +10, NTSC, R_L = 150Ω
G = +10, NTSC, R_L = 150Ω
Input Referred, f = 5MHz
V_O = 0V
V_CM = 0V
V_CM = 0V
V_CM = 0V
V_CM = 0V
V_CM = 0V
V_CM = 0V
V_CM = 0V, Input Referred
V_CM = 0V
V_CM = 0V
≥ 400Ω Load
100Ω Load
V_O = 0V
V_O = 0V
G = +10, f = 100kHz
V_S = ±5V
V_S = ±5V
|V_S| = 4.5 to 5.5, Input Referred
Junction-to-Ambient
425
250
100
1600
40
2
–72
–90
–95
–110
43
1.4
1.8
1.4
600
18
16
11
0.02
0.02
–70
80
±0.35
–10
±0.5
200
80
1250
35
–67
–85
–90
–105
40
1.6
2.3
1.75
500
14
12
75
±1.0
–17
±1.0
±3.2
±3.0
100
90
6 || 2
2.9 || 1
±3.5
±3.2
±3.3
±3.0
80
60
–80
–60
0.008
±5
±6
24.8
25.8
24.8
23.8
78
70
–40 to +85
125
170
65
1100
30
–65
–80
–85
–100
39
1.7
2.4
2
400
21
14
70
±1.2
5
–18
50
±1.5
5
±2.9
85
±3.1
±2.8
55
–55
±6
26
23.8
70
140
55
1000
25
–60
–75
–80
–95
37
1.8
2.5
2.5
310
25
18
MHz
typ C
MHz min B
MHz min B
MHz min B
MHz min B
dB
typ C
dBc max B
dBc max B
dBc max B
dBc
dBm
max B
min B
nV/√Hz max B
pA/√Hz max B
ns
V/µs
ns
ns
max B
min B
typ C
max B
ns
max B
%
typ C
deg
typ C
dBc
typ C
70
dB
min A
±1.5
mV
max A
10
µV/°C max B
–20
µA
max A
100
nA/°C max B
±1.8
µA
max A
10
nA/°C max B
±2.8
V
min A
75
dB
min A
kΩ || pF typ C
MΩ || pF typ C
±3.0
V
min A
±2.8
V
min A
50
mA
min A
–40
mA
min A
Ω
typ C
V
typ C
±6
V
max A
27.8
mA
max A
22
mA
min A
65
dB
min A
°C
typ C
°C/W typ C
NOTES: (1) Test Levels: (A) 100% tested at 25°C. Over temperature limits by characterization and simulation. (B) Limits set by characterization and simulation.
(C) Typical value only for information. (2) Junction temperature = ambient for 25°C guaranteed specifications. (3) Junction temperature = ambient at low temperature
limit: junction temperature = ambient +23°C at high temperature limit for over temperature guaranteed specifications. (4) Current is considered positive out-of-node.
V_CM is the input common-mode voltage. (5) Tested < 3dB below minimum specified CMR at ±CMIR limits.
®
OPA2686
2