SM015A100JAN120 Datasheet, PDF (98/112 Pages) AVX Corporation – AVX Advanced Ceramic Capacitors for Power Supply, High Voltage and Tip and Ring Applications

MLC Chips
Packaging of Chip Components
T2
D0
T _DEFORMATION
BETWEEN
EMBOSSMENTS
P0
P2
10 PITCHES CUMULATIVE
TOLERANCE ON TAPE
±0.2mm (±0.008)
EMBOSSMENT
E1
TOP COVER
B1
K0 ^TAPE
A0
B0
F
W
E2
Chip Orientation
S1
T1
CENTER LINES
OF CAVITY
P1
MAX. CAVITY
SIZE - SEE NOTE 1
D1 FOR COMPONENTS
2.00 mm x 1.20 mm AND
LARGER (0.079 x 0.047)
B1 IS FOR TAPE READER REFERENCE ONLY
INCLUDING DRAFT CONCENTRIC AROUND B0
User Direction of Feed
8mm, 12mm & 24mm Embossed Tape
Metric Dimensions Will Govern
CONSTANT DIMENSIONS
Tape Size
8mm
12mm
24mm
D₀
1.50
+0.10
-0.0
(0.059
+0.004
-0.0
)
E₁
P₀
1.75 ± 0.10 4.0 ± 0.10
(0.069 ± 0.004) (0.157 ± 0.004)
S₁ Min.
0.60
(0.024)
millimeters (inches)
T Max.
0.60
(0.024)
T₁
0.10
(0.004)
Max.
VARIABLE DIMENSIONS
Tape Size B₁
D₁
E₂
F
Max. Min. Min.
P₁
P₂
R
Min.
See Note 2
8mm
4.35 1.00 6.25 3.50 ± 0.05 4.00 ± 0.10 2.00 ± 0.05 25.0
(0.171) (0.039) (0.246) (0.138 ± 0.002) (0.157 ± 0.004) (0.079 ± 0.002) (0.984)
T₂
Max.
2.50
(0.098)
millimeters (inches)
W
Max.
A₀ B₀ K₀
8.30
(0.327) ^{See Note 1}
8.20 1.50 10.25 5.50 ± 0.05 4.00 ± 0.10 2.00 ± 0.05 30.0
12mm _{(0.323) (0.059) (0.404) (0.217 ± 0.002) (0.157 ± 0.004) (0.079 ± 0.002) (1.181)}
6.50
(0.256)
12.3
(0.484) ^{See Note 1}
12mm
Double
Pitch
8.20 1.50 10.25 5.50 ± 0.05 8.00 ± 0.10 2.00 ± 0.05 30.0
(0.323) (0.059) (0.404) (0.217 ± 0.002) (0.315 ± 0.004) (0.079 ± 0.002) (1.181)
6.50
(0.256)
12.3 _{See Note 1}
(0.484)
24mm
20.10 1.50 22.25 11.5 ± 0.10 16.00 ± 0.10 2.00 ± 0.10 30.0
(0.791) (0.059) (0.876) (0.453 ± 0.004) (0.630 ± 0.004) (0.079 ± 0.004) (1.181)
12.00
(0.472)
24.3
(0.957) ^{See Note 1}
NOTES:
1. The cavity defined by A0, B0, and K0 shall be configured to provide the following:
Surround the component with sufficient clearance such that:
a) the component does not protrude beyond the sealing plane of the cover tape.
b) the component can be removed from the cavity in a vertical direction without mechanical
restriction, after the cover tape has been removed.
c) rotation of the component is limited to 20º maximum (see Sketches D & E).
d) lateral movement of the component is restricted to 0.5mm maximum (see Sketch F).
2. Tape with or without components shall pass around radius “R” without damage.
3. Bar code labeling (if required) shall be on the side of the reel opposite the round sprocket holes.
Refer to EIA-556.
4. B1 dimension is a reference dimension for tape feeder clearance only.
Top View, Sketch "F"
Component Lateral Movements
0.50mm (0.020)
Maximum
Side or Front Sectional View
Sketch “D”
0.50mm (0.020)
Maximum
Top View
Sketch “E”
97