HCPL-0738-500E Datasheet, PDF (6/8 Pages) AVAGO TECHNOLOGIES LIMITED – High Speed CMOS Optocoupler

Package Characteristics
All typicals at T_A = 25˚C.
Parameter
Input-Output Insulation
Input-Output Momentary
Withstand Voltage
Input-Output Resistance
Input-Output Capacitance
Symbol
I_I-O
V_ISO
R_I-O
C_I-O
Min.
Typ.
3750
10¹²
0.6
Max.
Units Test Conditions
1
µA
45% RH, t = 5 s
V_I-O = 3 kV DC,
T_A = 25˚C
V rms RH ≤ 50%, t = 1 min.,
T_A = 25˚C
Ω
V_I-O = 500 V DC
pF
f = 1 MHz, T_A = 25˚C
Notes:
1. t_PHL propagation delay is measured from the 50% level on the rising edge of the input pulse to the 2.5 V level of the falling edge of the V_O
signal. t_PLH propagation delay is measured from the 50% level on the falling edge of the input pulse to the 2.5 V level of the rising edge of the
V_O signal.
2. PWD is defined as |t_PHL - t_PLH|.
3. t_PSK is equal to the magnitude of the worst case difference in t_PHL and/or t_PLH that will be seen between units at any given temperature within
the recommended operating conditions.
4. CM_H is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state.
5. CM_L is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state.
1000
100
10
1.0
I_F
+
V_F
–
T_A = 25°C
0.1
0.01
0.001
1.1 1.2 1.3 1.4 1.5 1.6
V_F – FORWARD VOLTAGE – V
8
7 VDD = 5.0 V
I_OL = 20 µA
6
5
4
I_th1
I_th2
3
2
1
0
-40 -20 0 20 40 60 80 100
T_A – TEMPERATURE – °C
10.0
V_DD = 5.0 V
9.5
9.0
8.5
I_ddh
8.0
7.5
7.0
6.5
6.0
-40 -20 0 20 40 60 80 100
T_A – TEMPERATURE – °C
Figure 1. Typical input diode forward characteristic.
Figure 2. Typical input threshold current vs. tempera-
ture.
Figure 3. Typical logic high O/P supply current vs.
temperature.
11.6
11.4
V_DD = 5.0 V
11.2
11.0
10.8
10.6
I_ddl
10.4
10.2
10.0
9.8
9.6
-40 -20 0 20 40 60 80 100
T_A – TEMPERATURE – °C
50
45
40
T_phl CH 1
35
T_phl CH 2
30
25
20
15 ^{PWD CH 1}
T_plh CH 1
T_plh CH 2
PWD CH 2
10
5
V_DD = 5.0 V
T_A = 25 °C
0
567 8
9 10 11 12 13 14
I_F – PULSE INPUT CURRENT – mA
Figure 4. Typical logic low O/P supply current vs.
temperature.

Figure 5. Typical switching speed vs. pulse input cur-
rent.
HCPL-0738 fig 5