5962-9314002HPA Datasheet, PDF (6/11 Pages) AVAGO TECHNOLOGIES LIMITED – 90 V/1.0 Ohm, Hermetically Sealed, Power MOSFET Optocoupler

Typical Characteristics
All typical values are at T_A = 25°C, I_F(ON) = 10 mA, V_F(OFF) = 0.6 V unless otherwise specified.
Parameter
Symbol Test Conditions
Typ. Units Fig. Notes
Output Off-Capacitance
C_O(OFF)
V_O = 28 V, f = 1 MHz
145
pF
16
Output Offset Voltage
Input Diode Temperature Coefficient
|V_OS|
'V_F/'T_A
I_F = 10 mA, I_O = 0 mA
I_F = 10 mA
2
PV
19
7
-1.4 mV/°C
Input Capacitance
C_IN
V_F = 0 V, f = 1MHz
20
pF
8
Input-Output Capacitance
Input-Output Resistance
C_I-O
V_I-O = 0 V, f = 1 MHz
R_I-O
V_I-O = 500 V, t = 60 s
1.5
pF
4
10¹³
:
4
Turn On Time With Peaking
t_ON
I_FPK = 100 mA, I_FSS = 10 mA
V_DD = 28 V, I_O = 800 mA
0.22 ms
1
6
Notes:
1. Maximum junction to case thermal resistance for the device is 15°C/W, where case temperature, T_C, is measured at the center of the package
bottom.
2. For rating, see Figure 4. The output power P_O rating curve is obtained when the part is handling the maximum average output current I_O as
shown in Figure 2.
3. During the pulsed R_ON measurement (I_O duration <30 ms), ambient (T_A) and case temperature (T_C) are equal.
4. Device considered a two terminal device: pins 1 through 4 shorted together and pins 5 through 8 shorted together.
5. This is a momentary withstand test, not an operating condition.
6. For a faster turn-on time, the optional peaking circuit shown in Figure 1 may be implemented.
7. V_OS is a function of I_F, and is defined between pins 5 and 8, with pin 5 as the reference. V_OS must be measured in a stable ambient (free of tem-
perature gradients).
8. Zero-bias capacitance measured between the LED anode and cathode.
9. Standard parts receive 100% testing at 25°C (Subgroups 1 and 9). SMD, Class H and Class E parts receive 100% testing at 25°C, 125°C and -55°C
(Subgroups 1 and 9, 2 and 10, 3 and 11 respectively).
10. Applies to HSSR-7112 and 5962-9314002Hxx devices only.
11. Applies to HSSR-7110, HSSR-7111, HSSR-711E, 5962-9314001Hxx and 5962-9314001Exx devices only.
V_CC (+5V)
IN
HSSR-7110
1
8
I_F
+2
7
V_F
-3
6
R2
1200 Ω
R3
4
5
R1
330 Ω
C
15 μF
1/4 54ACTOO
1/4 54ACTOO*
R1 = REQUIRED CURRENT LIMITING RESISTOR
FOR I_{F (ON)} = 10 mA.
R2 = PULL-UP RESISTOR FOR V_{F (OFF)} < 600 mV;
I_F (V_CC-V_OH ) < 600 mV, OMIT R2.
R3, C = OPTIONAL PEAKING CIRCUIT.
* USE SECOND GATE IF IF (PK) > 50 mA
REMINDER: TIE ALL UNUSED INPUTS TO GROUND OR V _CC
TYPICAL VALUES
R3
I_{F (PK)}
(Ω) (mA)
- _{10 (NO PK)}
330 ₂₀
100 ₄₀
33 ₁₀₀
HSSR-7110
t_ON (ms)
2.0
1.0
0.48
0.22
Figure 1. Recommended Input Circuit.
6