HCPL-2730-000E Datasheet, PDF (11/13 Pages) AVAGO TECHNOLOGIES LIMITED – Dual Channel Low Input Current, High Gain Optocouplers

Package Characteristics

Device
Parameter
Symbol HCPL- Min. Typ.* Max. Units Test Conditions
Fig.
Input-Output Momentary
V_ISO
3750 V rms RH ≤50%,
Withstand Voltage** t = 1 min.,
      Option 020
2730 5000 ^TA ^{= 25°C}

2731
Resistance
R_I-O
10¹²
Ω
(Input-Output)
V_I-O = 500 VDC
RH ≤45%
Capacitance
(Input-Output)
C_I-O 0.6 pF f = 1 MHz
Input-Input Insulation
I_I-I 0.005 µA
Leakage Current
RH ≤45%
V_I-I = 500 VDC
Input-Input Insulation
Leakage Current
R_I-I
10¹¹
Ω
Capacitance
C_I-I
(Input-Input)
2730
2731
0.03
pF


0730 0.25
0731
Note
4, 9
4, 10
4
11
5
5
5
*All Typical values at T_A = 25°C unless otherwise noted.
**The Input-Output Momentary Withstand Voltage is a dielectric voltage rating that should not be interpreted as an input-output continuous
voltage rating. For the continuous voltage rating refer to the IEC/EN/DIN EN 60747-5-2 Insulation Characteristics Table (if applicable), your equip-
ment level safety specification or Avago Application Note 1074 entitled “Optocoupler Input-Output Endurance Voltage.”
Notes:
  1. Pin 5 should be the most negative voltage at the detector side.
  2. Each channel.
  3. DC CURRENT TRANSFER RATIO (CTR) is defined as the ratio of output collector current, I_O, to the forward LED input current, I_F, times 100%.
  4. Device considered a two-terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together.
  5. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together.
  6. Common mode transient immunity in a Logic High level is the maximum tolerable (positive) dV_CM/dt of the common mode pulse, V_CM, to as-
sure that the output will remain in a Logic High state
(i.e., V_O > 2.0 V). Common mode transient immunity in a Logic Low
level is the maximum tolerable (negative) dV_CM/dt of the common mode pulse, V_CM, to assure that the output will remain in a Logic Low state
(i.e., V_O < 0.8 V).
  7. In applications where dV/dt may exceed 50,000 V/µs (such as static discharge) a series resistor, R_CC, should be included to protect the detec-
tor IC from destructively high surge currents. The recommended value is R_CC = 110 Ω.
  8. Use of a 0.1 µF bypass capacitor connected between pins 5 and 8 adjacent to the device is recommended.
  9. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 4500 V rms for 1 second (leakage
detection current limit,
I_I-O < 5 µA).
10. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage > 6000 V rms for 1 second (leakage
detection current limit,
I_I-O < 5 µA).
11. Measured between the LED anode and cathode shorted together and pins 5 through 8 shorted together.
12. Derate linearly above 65°C free-air temperature at a rate of 2.3 mW/°C for the SO-8 package.
11