8205-10 Datasheet, PDF (3/4 Pages) ASM GmbH – MICRO HiCORDER


Simple Operation, Rugged Design and Quiet !
Operational simplicity with
multimeter ease-of-use.
The 8206-10 has two recording channels,
one for voltage and one for current.
(clamp on sensor sold separately)
Intuitive analog dials are used to set the input
range and paper feed speed. This makes the
recorders as easy to operate as a multimeter.
With 2-channel recording, a single instrument
can simultaneously record both voltage and
current. This is ideal for management and
testing of power lines.
A sensor allow measurement up to
1000A.
(clamp on sensor sold separately)
Sensitized recording paper
provides clean, easy-to-read
printouts.
■ Paper feed speed and recording time
*With a time axis resolution of 80 points / DIV (1DIV=10mm)
8205-10
8206-10 ^{9235,9236-01 Sensitizedpaper}
Paper feed speed Paper feed speed 15m (49ft 2.5in) roll
20 cm (7.9 in)/m
−
1 hr 15 m
6 cm (2.36 in)/m
−
4 hr 10 m
60 cm (23.8 in)/m 60 cm (23.8 in)/hr
1 day 1 hr
−
60 cm (23.8 in)/hr
3 days 3 hr
10 cm (3.94 in)/hr 10 cm (3.94 in)/hr
6 days 6 hr
−
6 cm (2.36 in)/hr
10 days 10 hr
2 cm (0.79 in)/hr 2 cm (0.79 in)/hr
31 days 6 hr
The recorder provides selectable current ranges.
Used together with a special clamp on sensor,
this makes it possible to read values directly and
eliminates the need for scaling conversion. In
addition to 100A and 500A sensors, a sensor has
been added to allow measurement up to 1000A.
Sensitized recording paper is used, providing clean,
quiet recording. Further, HIOKI's RECORDING
PAPER 9236-01 and provides superior climate
resistance and is much less susceptible to
discoloration due to chemical exposure than
ordinary thermal recording paper, providing much
longer print life.
Adaptable for Special Applications
As a special-order option, the DC power supply connector
can be converted to a signal input terminal. Although this
makes it impossible to use a DC power supply, it allows
recording on paper to be turned on or off externally, or to
input a contact signal and record the occurrence of events
on recording paper. Please contact your nearest HIOKI
sales representive for details.
• Special order modification (disables DC power supply)
• External CHART ON / OFF control
• Event recording
Standard/Average Print Modes
Example of Instantaneous Power Outage Recording Also runs on DC Power !
AC/DC power supply
selector switch
Power switch
DC power inlet
AC power inlet
Standard Mode
Average Mode
For printing, you can select standard mode or average mode.
l Standard mode prints values interpolated from the maximum
and minimum values sampled every 10 ms. This is effective
for recording widths of steep input signal changes, such as
instantaneous power outages.
l Average mode prints the average value of the data during
the print interval. This makes it possible to print something
that is smooth and easy to see, at times when there are violent
fluctuations.
* Switch to average mode by holding down the paper feed button when turning on
the power.
50 Hz
60 Hz
This example shows recording of a
simulated instantaneous power outage by
the 8206, for AC 100V with frequencies of
50Hz or 60Hz and 0V durations of 0.5, 1, 2,
4, or 8 cycles.
Even for a 0.5 cycle instantaneous power
failure, the high speed response can
catch the line abnormality.
In addition to a universal power
AC supply of 100 to 240V, the
recorders can operate on 9.5 to
14V DC power supplies. This is
useful outdoors and in other field
applications.
* Runs off either AC or DC. DC cannot be
used as a backup power supply.