ALT6725 Datasheet, PDF (7/13 Pages) ANADIGICS, Inc – HELP3E Dual-band Cellular & PCS LTE 3.4 V Linear Power Amplifier Module

ALT6725
Table 7: Electrical Specifications - PCS Band (BC 1, 14)
(TC = +25 °C, VBATT = VCC = +3.4 V, VEN_PCS = +1.8 V, 50 Ω system, CDMA2000 RC-1 waveform)
PARAMETER
COMMENTS
MIN TYP MAX UNIT
POUT
VMODE1
VMODE2
-
27
-
+28 dBm 0 V
0V
Gain
-
13
-
dB +16 dBm 1.8 V
0V
-
9
-
+10 dBm 1.8 V
1.8 V
Adjacent Channel Power
at ± 1.25 MHz offset ⁽¹⁾
Primary Channel BW = 1.23 MHz
Adjacent Channel BW = 30 kHz
-
-48
-
- -52.5 -
-
-53
-
+28 dBm
dBc +16 dBm
+10 dBm
0V
1.8 V
1.8 V
0V
0V
1.8 V
Adjacent Channel Power
at ± 1.98 MHz offset ⁽¹⁾
Primary Channel BW = 1.23 MHz
Adjacent Channel BW = 30 kHz
-
-55
-
-
-60
-
-
-63
-
+28 dBm
dBc +16 dBm
+10 dBm
0V
1.8 V
1.8 V
0V
0V
1.8 V
Power-Added Efficiency ⁽¹⁾
-
37
-
-
20
-
-
10
-
+28 dBm 0 V
% +16 dBm 1.8 V
+10 dBm 1.8 V
0V
0V
1.8 V
Quiescent Current (Icq)
-
4
-
mA through VCC pins, VMODE1,2 = +1.8 V
Mode Control Current
-
0.5
-
mA through VMODE pin, VMODE1,2 = +1.8 V
BATT Current
-
1.5
-
mA through VBATT pin, VMODE1,2 = +1.8V
Enable Current
-
0.3
-
mA through VEN_PCS pin, VMODE1,2 = +1.8 V
Total Decoder Current on VBATT
(in Shutdown mode)
-
7
-
µA
VBATT = +4.35 V, VCC = +4.35 V,
VEN_CELL = 0 V, VMODE1,2 = 0 V
HBT Leakage Current on VCC
(in Shutdown mode)
-
<1
-
µA
VBATT = +4.35 V, VCC = +4.35 V,
VEN_CELL = 0 V, VMODE1,2 = 0 V
Noise In Receive Band
- -133 - dBm/Hz 1930 MHz to 1990 MHz
Harmonics
2fO
3fO, 4fO
-
-
-
-
-30
-30
dBc POUT < +28 dBm
Input Impedence
-
-
2:1 VSWR
Coupling Factor
-
22
-
dB
Spurious Output Level
(all spurious outputs)
POUT < +28 dBm
-
-
-65
dBc
In-band load VSWR < 5:1
Out-of-band load VSWR < 10:1
Applies over all operating conditions
Load mismatch stress with no
permanent degradation or failure
8:1
-
- VSWR Applies over full operating range
Notes:
(1) ACPRs and Efficiency measured at 1880 MHz.
7
PRELIMINARY DATA SHEET - Rev 1.0
07/2012