ALT6705 Datasheet, PDF (4/12 Pages) ANADIGICS, Inc – HELP4 UMTS800 (Bands 5, 6, 18, 19, & 26) LTE, WCDMA, CDMA Multimode PAM

ALT6705
Table 4: Electrical Specifications - LTE Operation (RB = 12, START = 0, QPSK)
(TC = +25 °C, VBATT = VCC =+3.4 V,VEN = +1.8 V, 50 Ω system)
PARAMETER
COMMENTS
MIN TYP MAX UNIT
POUT
VMODE1 VMODE2
Gain
ACLR E-UTRA
at  10 MHz offset
26 29 32
16 19 22
10 13.5 16
-
-41 -35
-
-40 -35
-
-40 -35
dB
POUT = +27.2 dBm 0 V
0V
POUT = +16 dBm 1.8 V 0 V
POUT =+7 dBm 1.8 V 1.8 V
POUT = +27.2 dBm 0 V
0V
dBc POUT = +16 dBm 1.8 V 0 V
POUT = +7 dBm
1.8 V 1.8 V
ACLR UTRA
at  7.5 MHz offset
-
-40 -36
POUT = +27.2 dBm 0 V
0V
-
-
-39 -36
-40 -36
dBc
POUT = +16 dBm
POUT = +7 dBm
1.8 V 0 V
1.8 V 1.8 V
ACLR UTRA
at  12.5 MHz offset
Power-Added Efficiency ⁽¹⁾
Quiescent Current (Icq)
Low Bias Mode
-
-60 -40
-
-58 -40
-
-57 -40
31 36
-
20 24
-
14 18
-
-
3
4.0
POUT = +27.2 dBm 0 V
0V
dBc POUT = +16 dBm 1.8 V 0 V
POUT = +7 dBm
1.8 V 1.8 V
POUT = +27.2 dBm 0 V
0V
% POUT = +16 dBm 1.8 V 0 V
POUT = +7 dBm
1.8 V 1.8 V
mA through VCC pin 1.8 V 1.8 V
Mode Control Current
-
0.06 0.15
mA through VMODE pins, VMODE = 1.8 V
Enable Current
-
0.04 0.12
mA through VEN pin
BATT Current
Leakage Current
-
0.7 1.2
mA
through VBATT pin, VMODE1 = +1.8 V,
VMODE2 = +1.8 V
VBATT = +4.35 V, VCC = +4.35 V,
-
<5 10
A VEN =0 V, VMODE = 0 V,
VMODE1 = 0 V
Noise in Receive Band
- -134 - dBm/Hz 869 MHz to 894 MHz
Harmonic
2fo
3fo, 4fo
-
-
-48 -35
-60 -42
dBc POUT 27.2 dBm
Coupling Factor
-
20
-
dB
Directivity
-
20
-
dB
Coupler IN_OUT
Daisy Chain Insertion Loss
- <0.3 -
dB
698 MHz to 2620 MHz
Pin 8 - 6, Shutdown Mode
Spurious Output Level
(all spurious outputs)
POUT < +27.2 dBm
-
-
<-70
dBc
In-band Load VSWR < 5:1
Out-of-band Load VSWR < 10:1
Applies over all operating conditions
Load mismatch stress with no
permanent degradation or failure
8:1
-
Notes:
(1) ACLR and Efficiency measured at 832 MHz.
- VSWR Applies over all operating conditions
4
Data Sheet - Rev 2.5
03/2012