ALT6702 Datasheet, PDF (4/12 Pages) ANADIGICS, Inc – HELP4 UMTS PCS (Band 2) LTE/WCDMA/CDMA Multi-Mode PAM

ALT6702
Table 4: Electrical Specifications - LTE Operation = 10 MHz QPSK 12 RB (Start = 0)
(TC = +25 °C, VBATT = VCC = +3.4 V,VENABLE = +1.8 V, 50 Ω system)
PARAMETER
COMMENTS
MIN TYP MAX UNIT
POUT
VMODE1
VMODE2
Gain
ACLR E-UTRA
at ± 10 MHz offset
ACLR UTRA
at ± 7.5 MHz offset
ACLR UTRA
at ± 12.5 MHz offset
Power-Added Efficiency
Ouiescent Current (Icq)
Low Bias Mode
Mode Control Current
Enable Current
BATT Current
Leakage Current
Noise Power
Harmonics
2fo
3fo, 4fo
Coupling Factor
Directivity
Coupler In_Out
Daisy Chain Insertion Loss
25 27.5
16
19
8 10.5
-
-39
-
-39
-
-40
-
-39
-
-40
-
-40
-
-59
-
-59
-
-60
31
34
26
30
19
23
-
2
-
0.08
-
0.04
-
0.8
-
<5
-
-135
-
-135
-
-146
-
-44
-
-50
-
20
-
20
- <0.25
Spurious Output Level
(all spurious outputs)
-
-
Load mismatch stress with no
permanent degradation or failure
8:1
-
Notes:
1. ACLR and Efficiency are measured at 1880 MHz.
30
22
13
-34
-34
-34
-36
-36
-36
-40
-40
-40
-
-
-
3.5
0.15
0.1
1.5
8
-133
-
-
-35
-42
-
-
-
<-70
-
POUT = +27.4 dBm 0 V
0V
dB POUT = +16.5 dBm 1.8 V 0 V
POUT = +8 dBm
1.8 V 1.8 V
POUT = +27.4 dBm 0 V
0V
dBc POUT = +16.5 dBm 1.8 V 0 V
POUT = +8 dBm
1.8 V 1.8 V
POUT = +27.4 dBm 0 V
0V
dBc POUT = +16.5 dBm 1.8 V 0 V
POUT = +8 dBm
1.8 V 1.8 V
POUT = +27.4 dBm 0 V
0V
dBc POUT = +16.5 dBm 1.8 V 0 V
POUT = +8 dBm
1.8 V 1.8 V
POUT = +27.4 dBm 0 V
0V
% POUT = +16.5 dBm 1.8 V 0 V
POUT = +8 dBm
1.8 V 1.8 V
mA through VCC pin 1.8 V 1.8 V
mA
through VMODE pins, VMODE1,2 = +1.8 V
mA through VEN pin , VEN = +1.8 V
mA
through VBATT pin, VMODE1,2 = +1.8 V
µA
VBATT = VCC = +4.35 V
VEN = 0 V, VMODE1,2 = 0 V
1930 MHz to 1990 MHz
dBm/Hz GPS Band
ISM Band
dBc POUT ≤ +27.4 dBm
dB
dB
dB
698 Mhz to 2620 MHz
Pin 8 to 9, Shutdown Mode
POUT < +27.4 dBm
dBc
In-band load VSWR < 5:1
Out-of-band load VSWR < 10:1
Applies over all operating ranges
VSWR Applies over full operating range
4
Data Sheet - Rev 2.5
03/2012