AMIS-710401 Datasheet, PDF (4/9 Pages) AMI SEMICONDUCTOR – 400dpi CIS Module

AMIS710401-A4: 400dpi CIS Module
Red 600nm LED Light Source
Data Sheet
7.0 Electro-Optical Characteristics at 25°C
Table 5 lists the fixed geometrical electro-optical characteristics. Table 6 shows the factory adjustable specification characteristics
constrained to the limits of the test target and the LED light source.
Table 5: Fixed Geometrical Electro-Optical Characteristics
Parameter
Value
Total number of pixels in each module
3456
Pixel-to-pixel spacing
62.5
Units
Elements
µm
7.1 Module: AMIS-710401-A4; Light Source: 660nm Red LED
Table 6: AMIS-710401-A4 / 660nm Red LED Electro-Optical Characteristics
Parameter
Line scanning rate ⁽¹⁾
Symbol
Tint
Value
692
Units
µsec
Note
@ 5.0MHz clock
Clock frequency⁽²⁾
Bright output voltage⁽³⁾⁽⁷⁾
Bright output non-uniformity⁽⁴⁾
Adjacent photo-response non-uniformity⁽⁵⁾
Dark non-uniformity⁽⁶⁾
Dark output voltage⁽⁷⁾
Modulation transfer function⁽⁸⁾
Fclk
Video output
Up
Upn
Ud
Dark level (DL)
MTF
5.0
1.25±0.25
< ±30
<25
< 150
< 100
> 40
MHz
V
%
%
mV
mV
%
frequency
Notes:
(1) Tint is the line-scanning rate or integration time and is determined by the interval between two start pulses (SP). The integration time is factory adjusted to give
1.25V output with the maximum clock frequency of 5MHz. However, a minimum integration of 630µs is with a maximum 5.5MHz clock frequency.
(2) Fclk is the main clock frequency and also equals the pixel rate.
(3) Video output level is dependent on the Integration time and the LED light power.
(4) Up = [Vp(max) - Vpavg] / Vpavg x 100% or [Vpavg - Vp(min)] / Vpavg} x 100%, whichever is greater.
Where Vp(max) = maximum pixel level, Vp(min) = minimum pixel level, and Vpavg = average of all pixels.
(5) Adjacent photo-response non-uniformity (Upn)
(6) Upn = Max ((Vpn – Vpn+1) / Min (Vpn, Vpn+1)) x 100%, where Vpn is the pixel output voltage of Pixel n in the light.
(7) Ud = Vdmax - Vdmin, where Vdmin is the minimum output voltage with the LED off and Vdmax is maximum output voltage with the LED on.
(8) See the paragraph in Section 9.0 for explanation.
(9) See the paragraph in Section 10.0. A graph of the typical MTF vs Depth of Focus is shown.
8.0 Recommended Operating Conditions at 25°C
Table 7 lists the recommended operating conditions. Table 8 lists the recommended operating conditions for t he LED light source.
Table 7: Recommended Operating Conditions at 25°C
Parameter
Symbol
Power supply
Vdd (positive)
Vn (negative)
Idd (positive)
In (negative)
Input voltage (high level)
Vih
Input voltage (low level)
Vil
Clock frequency ⁽¹⁾
Fclk
Clock pulse high duty cycle
Duty
Clock pulse high duration
Integration time⁽¹⁾
Pwck
Tint
Operating temperature
Top
Min.
4.5
-12
14
8
Vdd - 1.0
0
0.346
25
46
630
0
Typ.
5.0
-5
17
9
Vdd - 0.5
25
Max.
5.5
-4.5
20
10
Vdd
0.6
5.5
10000
50
Units
V
V
mA
mA
V
V
MHz
%
ns
µs
°_C
AMI Semiconductor – Jun. 06, M-20589-001
4
www.amis.com