|
EP4CE15F23C6N Datasheet, PDF (11/42 Pages) Altera Corporation – This section lists the I/O leakage current, pin capacitance, on-chip termination (OCT) tolerance, and bus hold specifications for Cyclone IV devices. | |||
|
◁ |
Chapter 1: Cyclone IV Device Datasheet
Operating Conditions
1â11
Internal Weak Pull-Up and Weak Pull-Down Resistor
Table 1â12 lists the weak pull-up and pull-down resistor values for Cyclone IV
devices.
Table 1â12. Internal Weak Pull-Up and Weak Pull-Down Resistor Values for Cyclone IV Devices (1)
Symbol
Parameter
Conditions
Min Typ Max Unit
VCCIO = 3.3 V ± 5% (2), (3)
Value of the I/O pin pull-up resistor
VCCIO = 3.0 V ± 5% (2), (3)
R_PU
before and during configuration, as
well as user mode if you enable the
VCCIO = 2.5 V ± 5% (2), (3)
VCCIO = 1.8 V ± 5% (2), (3)
programmable pull-up resistor option VCCIO = 1.5 V ± 5% (2), (3)
7
25 41 kï
7
28 47 kï
8
35 61 kï
10 57 108 kï
13 82 163 kï
VCCIO = 1.2 V ± 5% (2), (3)
VCCIO = 3.3 V ± 5% (4)
VCCIO = 3.0 V ± 5% (4)
R_PD
Value of the I/O pin pull-down resistor
before and during configuration
VCCIO = 2.5 V ± 5% (4)
VCCIO = 1.8 V ± 5% (4)
VCCIO = 1.5 V ± 5% (4)
19 143 351 kï
6
19 30 kï
6
22 36 kï
6
25 43 kï
7
35 71 kï
8
50 112 kï
Notes to Table 1â12:
(1) All I/O pins have an option to enable weak pull-up except the configuration, test, and JTAG pins. The weak pull-down feature is only available
for JTAG TCK.
(2) Pin pull-up resistance values may be lower if an external source drives the pin higher than VCCIO.
(3) R_PU = (VCCIO â VI)/IR_PU
Minimum condition: â40°C; VCCIO = VCC + 5%, VI = VCC + 5% â 50 mV;
Typical condition: 25°C; VCCIO = VCC, VI = 0 V;
Maximum condition: 100°C; VCCIO = VCC â 5%, VI = 0 V; in which VI refers to the input voltage at the I/O pin.
(4) R_PD = VI/IR_PD
Minimum condition: â40°C; VCCIO = VCC + 5%, VI = 50 mV;
Typical condition: 25°C; VCCIO = VCC, VI = VCC â 5%;
Maximum condition: 100°C; VCCIO = VCC â 5%, VI = VCC â 5%; in which VI refers to the input voltage at the I/O pin.
Hot-Socketing
Table 1â13 lists the hot-socketing specifications for Cyclone IV devices.
Table 1â13. Hot-Socketing Specifications for Cyclone IV Devices
Symbol
Parameter
Maximum
IIOPIN(DC)
IIOPIN(AC)
DC current per I/O pin
AC current per I/O pin
300 ïA
8 mA (1)
IXCVRTX(DC)
DC current per transceiver TX pin
100 mA
IXCVRRX(DC)
DC current per transceiver RX pin
50 mA
Note to Table 1â13:
(1) The I/O ramp rate is 10 ns or more. For ramp rates faster than 10 ns, |IIOPIN| = C dv/dt, in which C is the I/O pin
capacitance and dv/dt is the slew rate.
1 During hot-socketing, the I/O pin capacitance is less than 15 pF and the clock pin
capacitance is less than 20 pF.
December 2013 Altera Corporation
Cyclone IV Device Handbook,
Volume 3
|
▷ |