700-SH Datasheet, PDF (6/7 Pages) Allen-Bradley – Solid-State Relays

Bulletin 700-SH
Solid-State Relays
Approximate Dimensions
Mounting Considerations➊➋➌➍➎
All units are in millimeters unless otherwise indicated. Dimensions are not intended for manufacturing purposes.
Four, M4 x 8
4.5 dia. screws
Mounting Holes
Terminal Arrangement/
Internal Connections (Top
View)
58 max. 47.5 44
Cat. No. 700-SH05…
4.5
25
43 max.
Operating
indicator
13.8
25 max.
27 max.
4.5 dia. Two, M5 x 12 screws
Two, 4.3-dia.
or M4 holes
Load
47.6±0.2
Load
1
2
(-)
(+)
4
3
Input
Mounting Holes
Load
power
supply
58 min.47.5 44
Two, 4.3-dia.
or M4 holes
Cat. No. 700-SH40
4.5
25
43 max.
Operating
indicator
Two,
M4x8
13.8
25 max.
27 max.
47.6±0.2
➊ The proper mounting orientation of the heat sink is so the heat fins run perpendicular to the floor (vertical) to maximize ventilation flow.
➋ If the fins do not run perpendicular to the floor, a 30% current derating is required.
➌ When attaching a heat sink to Bulletin 700-SH, apply heat conductive grease on the heat sink to maximize heat transfer between the SSR and the heat sink.
Recommended types: Silicon based, Toshiba YG6240; Non-silicon based, AOS company type 53300.
➍ Tighten the SSR panel/heat sink mounting screws to a torque of 0.78…0.98 Nm (6.9…8.7 lb-in).
➎ Tighten the SSR terminal wiring screws as follows M4: 0.98…1.37 Nm (8.67…12.12 lb-in.), M5: 1.57…2.35 Nm (13.89…20.8 lb-in.)
Heat Sinks➏ ➐
4.6 dia.
Two, M3 holes
Two, M4 holes
Two, 3.2-dia.
holes
35±0.2
Mounting Holes
35 30.5 0.3
44 max. 30
47 max.
4.6 dia.
47.6
77 max.
90±0.3
100 max.
5.6
5
6
4.5
51 max.
Cat. No. 700-S10
Two, M3 holes ^{Two, M4}
holes
Two, 3.2-dia. holes
90±0.4
Two, 4.4-dia.
or M4 holes
35±0.2
Mounting Holes
35 30.5±0.3
71 max.
30
75 max.
4.6 dia.
47.6
77 max.
90±0.3
100 max.
47.6
5.6
Three,
M4
holes
28
5
13
4.5
100 max.
Cat. No. 700-S20
Two, 3.2-dia. holes
90±0.4
35±0.2
Two, 4.4-dia.
or M4 holes
Mounting Holes
35
100 max. 30
104 max.
Two, 4.4-dia.
or M4 holes
90±0.4
56±0.3
5.6
77 max.
90±0.3
100 max.
28
5
13
4.5
100 max.
Cat. No. 700-S30
➏ Tighten the heat sink mounting screws (M4) to a torque of 0.98…1.37 Nm (8.67…12.12 lb-in).
➐ Heat sink weight: cat. nos. 700-S10 = 200 g, 700-S20 = 400 g, 700-S30 = 560 g
56