AKD4356 Datasheet, PDF (19/27 Pages) Asahi Kasei Microsystems – EVALUATION BOARD REV.B FOR AK4356

ASAHI KASEI
[AKD4356 Control Program]
At first the following message is displayed:
****** AK4356 Control Program ver 1.0 , '99/3 ******
copyright(c) 1999, Asahi Kasei Microsystems co.,ltd.
All rights reserved.
Input Chip Address(CAD1,CAD0) (2 figure, binary) =
Input chip address in 2 figures of binary.
Set CAD1 and CAD0 before the AKD4356 is powered up.
When hanging CAD1 and CAD0, set SW1(-PD) “L”, then “H” after that.
After chip address is defined, the following default register map is displayed (Loop starts from here):
CAD1-0=00 ----------------------------------------------------------------
ADDR = 00 : 01 <Control 1> ( 0 SLOW DZFM DZFE DIF2 DIF1 DIF0 RSTN )
ADDR = 01 : 01 <Control 2> ( 0
0 0 CKS2 CKS1 CKS0 SMUTE RSTN )
ADDR = 02 : 0F <Speed & PD> ( 0
0 DFS1 DFS0 PW3 PW2 PW1 RSTN )
ADDR = 03 : 15 <DEM control>( 0
0 DEMC1 DEMC0 DEMB1 DEMB0 DEMA1 DEMA0)
ADDR = 04 : FF <LOUT1 ATT> ( ATT7 ATT6 ATT5 ATT4 ATT3 ATT2 ATT1 ATT0 )
ADDR = 05 : FF <ROUT1 ATT> ( ATT7 ATT6 ATT5 ATT4 ATT3 ATT2 ATT1 ATT0 )
ADDR = 06 : FF <LOUT2 ATT> ( ATT7 ATT6 ATT5 ATT4 ATT3 ATT2 ATT1 ATT0 )
ADDR = 07 : FF <ROUT2 ATT> ( ATT7 ATT6 ATT5 ATT4 ATT3 ATT2 ATT1 ATT0 )
ADDR = 08 : FF <LOUT3 ATT> ( ATT7 ATT6 ATT5 ATT4 ATT3 ATT2 ATT1 ATT0 )
ADDR = 09 : FF <ROUT3 ATT> ( ATT7 ATT6 ATT5 ATT4 ATT3 ATT2 ATT1 ATT0 )
ADDR = 0A : 00 <Test>
( TEST7 TEST6 TEST5 TEST4 TEST3 TEST2 TEST1 TEST0)
Input 1(Write), R(Reset), T(Table), I(Increment), D(Decrement) or S(Stop) :
1) If you input “1”, you can write data to AK4356.
You can write data to AK4356
Input Register Address (2 figure, hex) (00-0A) =
Input register address in 2 figures of hexadecimal.
Then current data of this address is displayed:
ADDR = 00 : 01 <Control 1> ( 0 SLOW DZFM DZFE DIF2 DIF1
000
0
00
Input Register Data (2 figure, hex) (00-FF) =
You can write control data to this address. Input control data in 2 figures of hexadecimal.
Refer to datasheet of AK4356.
Then the data written to this address is displayed:
ADDR = 00 : 07 <Control 1> ( 0 SLOW DZFM DZFE DIF2 DIF1
000
0
01
DIF0
0
DIF0
1
RSTN )
1
RSTN )
1
‘99/3
-2-