5962-8770102RA Datasheet, PDF (6/8 Pages) Analog Devices – CMOS Dual 8-Bit Buffered Multiplying DAC

AD7528
APPLICATIONS INFORMATION
Application Hints
To ensure system performance consistent with AD7528 specifi-
cations, careful attention must be given to the following points:
1. GENERAL GROUND MANAGEMENT: AC or transient
voltages between the AD7528 AGND and DGND can cause
noise injection into the analog output. The simplest method
of ensuring that voltages at AGND and DGND are equal is
to tie AGND and DGND together at the AD7528. In more
complex systems where the AGND–DGND intertie is on the
backplane, it is recommended that diodes be connected in
inverse parallel between the AD7528 AGND and DGND
pins (1N914 or equivalent).
2. OUTPUT AMPLIFIER OFFSET: CMOS DACs exhibit a
code-dependent output resistance which in turn causes a
code-dependent amplifier noise gain. The effect is a code-
dependent differential nonlinearity term at the amplifier
output which depends on V_OS (V_OS is amplifier input offset
voltage). This differential nonlinearity term adds to the R/2R
differential nonlinearity. To maintain monotonic operation, it
is recommended that amplifier V_OS be no greater than 10% of
1 LSB over the temperature range of interest.
3. HIGH FREQUENCY CONSIDERATIONS: The output
capacitance of a CMOS DAC works in conjunction with the
amplifier feedback resistance to add a pole to the open loop
response. This can cause ringing or oscillation. Stability can
be restored by adding a phase compensation capacitor in
parallel with the feedback resistor.
DYNAMIC PERFORMANCE
The dynamic performance of the two DACs in the AD7528 will
depend upon the gain and phase characteristics of the output
amplifiers together with the optimum choice of the PC board
layout and decoupling components. Figure 6 shows the relation
–100
–90
–80
–70
–60
T_A = +25؇C
V_DD = +15V
V_IN = 20V PEAK TO PEAK
ship between input frequency and channel to channel isolation.
Figure 7 shows a printed circuit layout for the AD7528 and the
AD644 dual op amp which minimizes feedthrough and crosstalk.
SINGLE SUPPLY APPLICATIONS
The AD7528 DAC R-2R ladder termination resistors are con-
nected to AGND within the device. This arrangement is par-
ticularly convenient for single supply operation because AGND
may be biased at any voltage between DGND and V_DD. Figure
8 shows a circuit which provides two +5 V to +8 V analog out-
puts by biasing AGND +5 V up from DGND. The two DAC
reference inputs are tied together and a reference input voltage
is obtained without a buffer amplifier by making use of the
constant and matched impedances of the DAC A and DAC B
reference inputs. Current flows through the two DAC R-2R
ladders into R1 and R1 is adjusted until the V_REF A and V_REF B
inputs are at +2 V. The two analog output voltages range from
+5 V to +8 V for DAC codes 00000000 to 11111111.
V_DD = +15V
DATA
INPUTS
CS
WR
DAC A/DAC B
2 VOLTS
R1
10k⍀
R2
1k⍀
DAC A
DB0
DB7
AD7528
DAC B
V_OUT A = +5V TO +8V
SUGGESTED
OP AMP:
AD644
V_OUT B = +5V TO +8V
AD584J
V_DD
GND
Figure 8. AD7528 Single Supply Operation
Figure 9 shows DAC A of the AD7528 connected in a positive
reference, voltage switching mode. This configuration is useful
in that V_OUT is the same polarity as V_IN allowing single supply
operation. However, to retain specified linearity, V_IN must be in
the range 0 V to +2.5 V and the output buffered or loaded with
a high impedance, see Figure 10. Note that the input voltage is
connected to the DAC OUT A and the output voltage is taken
from the DAC V_REF A pin.
V_IN (0V TO +2.5V)
V_REF A
V_OUT
–50
20k
50k 100k 200k
500k
1M
INPUT FREQUENCY – Hz
Figure 6. Channel-to-Channel Isolation
AD644
PIN 8 OF TO-5 CAN (AD644)
V+
V–
AGND
AD7528 PIN 1
C1 LOCATION
V_REF B*
V_DD
WR
CS
LSB
AD7528
C2 LOCATION
V_REF A*
DGND
DAC A/DAC B
MSB
*NOTE
INPUT SCREENS
TO REDUCE
FEEDTHROUGH.
LAYOUT SHOWS
COPPER SIDE
(i.e., BOTTOM VIEW).
Figure 7. Suggested PC Board Layout for AD7528 with
AD644 Dual Op Amp
V_DD
+15V
DAC A
AD7528
OUT A
Figure 9. AD7528 in Single Supply, Voltage Switching Mode
3
T_A = +25؇C
V_DD = +15V
2
NONLINEARITY
1
DIFFERENTIAL
NONLINEARITY
2.5 3 3.5 4 4.5 5 5.5 6 6.5 7 7.5
V_INA – Volts
Figure 10. Typical AD7528 Performance in Single Supply
Voltage Switching Mode (K/B/T, L/C/U Grades)
–6–
REV. B