X25643 Datasheet, PDF (8/16 Pages) Xicor Inc. – Programmable Watchdog Timer & V CC Supervisory Circuit w/Serial E 2 PROM

X25643/45
X25323/25
X25163/65
ABSOLUTE MAXIMUM RATINGS*
*COMMENT
Temperature under Bias ........................–65°C to +135°C
Storage Temperature .............................–65°C to +150°C
Voltage on any Pin with Respect to V_SS....... –1.0V to +7V
D.C. Output Current ....................................................5mA
Lead Temperature (Soldering, 10 seconds)............ 300°C
RECOMMENDED OPERATING CONDITIONS
Stresses above those listed under “Absolute Maximum
Ratings” may cause permanent damage to the device.
This is a stress rating only and the functional operation of
the device at these or any other conditions above those
listed in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
Temp
Commercial
Industrial
Min.
0°C
–40°C
Max.
70°C
+85°C
Supply Voltage
X25xxx–1.8
X25xxx–2.7
Limits
1.8V-3.6V
2.7V to 5.5V
7036 FRM T07
X25xxx
4.5V-5.5V
7036 FRM T08
D.C. OPERATING CHARACTERISTICS (Over the recommended operating conditions unless otherwise specified.)
Symbol
Parameter
I_CC1 V_CC Write Current (Active)
Limits
Min. Typ. Max.
5
Units
Test Conditions
mA
SCK = V_CC x 0.1/V_CC x 0.9 @ 2MHz,
SO = Open
I_CC2 V_CC Read Current (Active)
0.4
mA
SCK = V_CC x 0.1/V_CC x 0.9 @ 2MHz,
SO = Open
I_SB1 V_CC Standby Current WDT=OFF
1
µA CS = V_CC, V_IN = V_SS or V_CC, V_CC = 5.5V
I_SB2 V_CC Standby Current WDT=ON
50
µA CS = V_CC, V_IN = V_SS or V_CC, V_CC = 5.5V
I_SB3 V_CC Standby Current WDT=ON
20
µA CS = V_CC, V_IN = V_SS or V_CC, V_CC =3.6V
I_LI
Input Leakage Current
0.1 10
µA V_IN = V_SS to V_CC
I_LO
Output Leakage Current
0.1 10
µA V_OUT = V_SS to V_CC
V_IL⁽¹⁾
V_IH⁽¹⁾
V_OL1
Input LOW Voltage
Input HIGH Voltage
Output LOW Voltage
–0.5
V_CCx0.7
V_CCx0.3 V
V_CC+0.5 V
0.4
V V_CC > 3.3V, I_OL = 2.1mA
V_OL2 Output LOW Voltage
0.4
V 2V < V_CC ≤ 3.3V, I_OL = 1mA
V_OL3 Output LOW Voltage
0.4
V V_CC ≤ 2V, I_OL = 0.5mA
V_OH1 Output HIGH Voltage
V_CC–0.8
V V_CC > 3.3V, I_OH = –1.0mA
V_OH2 Output HIGH Voltage
V_CC–0.4
V 2V < V_CC ≤ 3.3V, I_OH = –0.4mA
V_OH3 Output HIGH Voltage
V_CC–0.2
V V_CC ≤ 2V, I_OH = –0.25mA
V_OLRS Reset Output LOW Voltage
0.4
V I_OL = 1mA
POWER-UP TIMING
7036 FRM T09
Symbol
t_PUR⁽²⁾
t_PUW⁽²⁾
Parameter
Power-up to Read Operation
Power-up to Write Operation
CAPACITANCE T_A = +25°C, f = 1MHz, V_CC = 5V.
Symbol
Test
C_OUT^{(2) Output Capacitance (SO, RESET, RESET)}
C_IN⁽²⁾
Input Capacitance (SCK, SI, CS, WP)
Notes: (1) V_IL min. and V_IH max. are for reference only and are not tested.
(2) This parameter is periodically sampled and not 100% tested.
Min.
Max.
8
6
Max.
1
5
Units
pF
pF
Units
ms
ms
7036 FRM T10
Conditions
V_OUT = 0V
V_IN = 0V
7036 FRM T11
8