W72M64VK-XBX Datasheet, PDF (3/16 Pages) White Electronic Designs Corporation – 2Mx64 3.3V Simultaneous Operation Flash Multi-Chip Package

White Electronic Designs
W72M64VK-XBX
ABSOLUTE MAXIMUM RATINGS
Parameter
Operating Temperature
Unit
-55 to +125
°C
Supply Voltage Range (VCC)
Signal Voltage Range
Storage Temperature Range
-0.5 to +4.0
V
-0.5 to Vcc +0.5
V
-55 to +150
°C
Endurance (write/erase cycles)
1,000,000 min. cycles
NOTES:
1. Stresses above the absolute maximum rating may cause permanent damage to the
device. Extended operation at the maximum levels may degrade performance and
affect reliability.
RECOMMENDED OPERATING CONDITIONS
Parameter
Symbol Min
Max
Unit
Supply Voltage
VCC
3.0
3.6
V
Operating Temp. (Mil.)
TA
-55
+125
°C
Operating Temp. (Ind.)
TA
-40
+85
°C
CAPACITANCE
TA = +25°C, F = 1.0MHz
Parameter
Symbol Max
WE1-4# capacitance
CWE
8
CS1-4# capacitance
CCS
8
Data I/O capacitance
CI/O
10
Address input capacitance
CAD
30
RESET# capacitance
CRS
26
RY/BY# capacitance
CRB
26
OE# capacitance
COE
32
This parameter is guaranteed by design but not tested.
Parameter
Pattern Data
Retention Time
DATA RETENTION
Test Conditions Min
150°C
10
125°C
20
Unit
pF
pF
pF
pF
pF
pF
pF
Unit
Years
Years
DC CHARACTERISTICS – CMOS COMPATIBLE
VCC = 3.3V ± 0.3V, -55°C ≤ TA ≤ +125°C
Parameter
Symbol Conditions
Min
Max
Unit
Input Leakage Current
ILI
VCC = 3.6V, VIN = GND to VCC
-10
10
µA
Output Leakage Current
ILO
VCC = 3.6V, VOUT = GND to VCC
-10
10
µA
VCC Active Current for Read (1)
ICC1 CS# = VIL#, OE = VIH, f = 5MHz
65
mA
VCC Active Current for Program or Erase (2,3)
ICC2 CS# = VIL#, OE = VIH, WE# = VIL
120
mA
VCC Standby Current (2)
ICC3 CS# = RESET# = VCC ± 0.3V
400
µA
Automatic Sleep Mode (2,4,5)
ICC5
VIH = VCC ± 0.3V;
VIL = VSS ± 0.3V
400
µA
VCC Active Read-While-Program Current (1,2)
ICC6 CS# = VIL#, OE = VIH
180
mA
VCC Active Program-While-Erase Current (1,2)
ICC7 CS# = VIL#, OE = VIH
180
mA
VCC Active Program-While-Erase-Suspended Current (2,5)
ICC8 CS# = VIL#, OE = VIH
140
mA
ACC Accelerated Program Current
IACC CS# = VIL#, OE = VIH ACC Pin
40
mA
VCC Pin
120
Input Low Voltage
VIL
-0.5
0.8
V
Input High Voltage
VIH VCC = min
2.1
VCC + 0.3
V
Voltage for WP#/ACC Sector
Protect/Unprotect and Program Acceleration
VHH VCC = 3.0V + 0.3V
8.5
9.5
V
Voltage for Autoselect and Temporary Sector Unprotect
VID VCC = 3.0V + 0.3V
8.5
12.5
V
Output Low Voltage
VOL IOL = 4.0 mA, VCC = 3.0V
0.45
V
Output High Voltage
VOH1 IOH = -2.0 mA, VCC = 3.0V
2.55
V
Low VCC Lock-Out Voltage (5)
VLKO
2.3
2.5
V
NOTES:
1. The ICC current listed includes both the DC operating current and the frequency dependent component (at 5 MHz).
The frequency component typically is less than 8 mA/MHz, with OE# at VIH.
2. Maximum ICC specifications are tested with VCC = VCC MAX
3. ICC active while Embedded Algorithm (program or erase) is in progress.
4. Automatic sleep mode enables the low power mode when addresses remain stable for tACC + 30ns.
5. Not tested.
April 2005
Rev. 0
3
White Electronic Designs Corporation • [phone] • www.wedc.com