JFCW10 Datasheet, PDF (1/5 Pages) Wall Industries,Inc. – 10 Watt DC/DC Power Converters

Wall Industries, Inc.
Rev B
JFCW10 SERIES
10 Watt DC/DC Power Converters
Size:
1.00 x 1.00 x 0.39 inches
(25.4 x 25.4 x 9.9 mm)
Options:
 Negative Logic Remote ON/OFF
 Without Trim pin
 Without CTRL Pin
 Heatsink
FEATURES
 High Efficiency up to 91%
 Remote On/Off Control
 4:1 Ultra Wide Input Voltage Ranges
 Six‐Sided Continuous Shielding
 Ultra Low Quiescent Current
 No Minimum Load Requirements
 Single and Dual Outputs
 Fixed Switching Frequency
 Built‐in EN55022 Class B Filter
 10 Watts Maximum Output Power
 Short Circuit, Over Voltage, Over Load, & Under‐Voltage Protection
 Wide Operating Temperature Range: ‐40°C to +85°C
 Compliant to RoHS EU Directive 2011/65/EU
 UL60950‐1, EN60950‐1, & IEC60950‐1 Safety Approvals
 CE Mark meets 2006/95/EC, 2011/95/EC, and 2004/108/EC
 Optional Heatsink Available (Suffix “HC”)
DESCRIPTION
The JFCW10 series of DC/DC power converters provides 10 Watts of output power in an industry standard 1.00” x
1.00” x 0.39” package and footprint. This series has single and dual output models with 4:1 ultra wide input voltage
ranges of 9‐36VDC and 18‐75VDC. Some features include high efficiency up to 91%, 1600VDC I/O isolation, six‐sided
shielding, and remote on/off control. These converters are also protected against short circuit, over voltage, over
load, and under‐voltage. All models are RoHS compliant and have UL60950‐1, EN60950‐1, and IEC60950‐1 safety
approvals. This series is best suited for use in wireless networks, telecom/datacom, industry control systems,
measurement equipment, and semiconductor equipment.
Model Number
JFCW24S33‐10
JFCW24S05‐10
JFCW24S12‐10
JFCW24S15‐10
JFCW24S24‐10
JFCW48S33‐10
JFCW48S05‐10
JFCW48S12‐10
JFCW48S15‐10
JFCW48S24‐10
Input Voltage Range
24 VDC
(9 – 36 VDC)
48 VDC
(18 – 75 VDC)
Model Number
JFCW24D05‐10
JFCW24D12‐10
JFCW24D15‐10
JFCW48D05‐10
JFCW48D12‐10
JFCW48D15‐10
Input Voltage Range
24 VDC
(9 – 36 VDC)
48 VDC
(18 – 75 VDC)
Output
Voltage
3.3 VDC
5 VDC
12 VDC
15 VDC
24 VDC
3.3 VDC
5 VDC
12 VDC
15 VDC
24 VDC
Output
Voltage
±5 VDC
±12 VDC
±15 VDC
±5 VDC
±12 VDC
±15 VDC
MODEL SELECTION TABLE
SINGLE OUTPUT MODELS
Output Current
Output
Min Load Max Load Ripple & Noise
0mA
3000mA
40mVp‐p
0mA
2000mA
40mVp‐p
0mA
830mA
60mVp‐p
0mA
670mA
60mVp‐p
0mA
416mA
60mVp‐p
0mA
3000mA
40mVp‐p
0mA
2000mA
40mVp‐p
0mA
830mA
60mVp‐p
0mA
670mA
60mVp‐p
0mA
416mA
60mVp‐p
DUAL OUTPUT MODELS
Output Current
Output
Min Load Max Load Ripple & Noise
0mA
±1000mA
40mVp‐p
0mA
±416mA
60mVp‐p
0mA
±333mA
60mVp‐p
0mA
±1000mA
40mVp‐p
0mA
±416mA
60mVp‐p
0mA
±333mA
60mVp‐p
No Load
Input Current
6mA
6mA
6mA
6mA
6mA
4mA
4mA
4mA
4mA
4mA
No Load
Input Current
6mA
6mA
6mA
4mA
4mA
4mA
Output
Power
9.9W
10W
10W
10W
10W
9.9W
10W
10W
10W
10W
Output
Power
10W
10W
10W
10W
10W
10W
Efficiency
85%
87%
90%
91%
90%
85%
87%
90%
90%
90%
Maximum
Capacitive Load
3500µF
2500µF
430µF
350µF
125µF
3500µF
2500µF
430µF
350µF
125µF
Efficiency
87%
89%
89%
87%
89%
89%
Maximum
Capacitive Load
±1440µF
±250µF
±180µF
±1440µF
±250µF
±180µF
NOTES
1. Trimming allows the user to increase or decrease the output voltage set point of the module. This is accomplished by connecting an external resistor
between the Trim pin and either the +Vout pin or the –Vout pin.
2. An external input filter capacitor is required if the module has to meet EN61000‐4‐4, EN61000‐4‐5. The filter capacitor suggested is Nippon chemi‐con KY
series, 220µF/100V.
3. The JFCW10 series standard modules meet EN55022 Class A without external components and meets Class B with external components. See page 4 for more
details.
4. Both positive logic and negative logic remote on/off control is available. Positive logic remote on/off comes standard; for negative logic remote on/off add
the suffix “R” to the model number (Ex: JFCW24S05‐10R).
5. There are several different options available for this series. Please see the “Model Number Setup” on page 5 for all options and ordering information.
6. Optional heatsink is available. Please call factory for more information.
CAUTION: This power module is not internally fused. An input line fuse must always be used.
10/31/2014
Wall Industries, Inc. • 37 Industrial Drive, Exeter, NH 03833 • Tel: 603‐778‐2300 • Toll Free: 888‐597‐9255 • Fax 603‐778‐9797
website: www.wallindustries.com • e‐mail: [e-mail]
Page 1 of 5