DG611A Datasheet, PDF (6/11 Pages) Vishay Siliconix – 1 pC Charge Injection, 100 pA Leakage, Quad SPST Switches

DG611A/DG612A/DG613A
Vishay Siliconix
New Product
SPECIFICATIONS FOR UNIPOLAR SUPPLIES V+ = + 3 V, V- = 0 V
Parameter
Analog Switch
Symbol
Test Conditions
Unless Specified
V+ = + 3 V, V- = 0 V
V_IN = 1.4 V, 0.6 V^a
- 40 to 125 °C
Temp.^b Typ.^c Min.^d Max.^d
Analog Signal Range^e
On-Resistance
V_ANALOG
r_ON
I_S = 1 mA, V_D = + 1.5 V
Full
Room 195
Full
0
3
235
300
Switch Off
Leakage Current
I_S(off)
I_D(off)
V+ = 3.3 V, V- = 0 V
V_D = 3 V/0.3 V
V_S = 0.3 V/3 V
Room ± 0.02 - 0.1 0.1
Full
-2
2
Room ± 0.02 - 0.1 0.1
Full
-2
2
Switch On
Leakage Current
Digital Control
I_D(on)
V+ = 3.3 V, V- = 0 V
V_D = V_S = 0.3 V/3 V
Room ± 0.02 - 0.1 0.1
Full
-6
6
Input Current, V_IN Low
I_IL
V_IN Under Test = 0.6 V
Full 0.005 - 0.1 0.1
Input Current, V_IN High
I_IH
Input Capacitance^e
C_IN
Dynamic Characteristics
V_IN Under Test = 1.4 V
f = 1 MHz
Full 0.005 - 0.1 0.1
Room
2
Turn-On Time
Turn-Off Time
t_ON
Room
87
R_L = 300 Ω, C_L = 35 pF
Full
125
180
t_OFF
V_S = 2 V, see Figure 1
Room
33
Full
55
65
Break-Before-Make
Time Delay
Charge Injection^e
Off Isolation^e
Channel-to-Channel
Crosstalk^e
t_BBM
DG613 only, V_S = 2 V
Room
60
R_L = 300 Ω, C_L = 35 pF
Full
10
Q
V_g = 0 V, R_g = 0 Ω, C_L = 1 nF Room
2.3
OIRR
X_TALK
R_L = 50 Ω, C_L = 5 pF
f = 10 MHz
Room - 60
Room - 90
3 dB Bandwidth^e
Source Off Capacitance^e
Drain Off Capacitance^e
BW
C_S(off)
C_D(off)
R_L = 50 Ω, C_L = 5 pF
f = 1 MHz; V_S = 0 V
Room 550
Room
5
Room
6
Drain On Capacitance^e
Power Supplies
C_D(on)
f = 1 MHz; V_S = V_D = 0 V Room
9
Power Supply Current
I+
Room 0.001
0.1
Full
1
Negative Supply Current
I-
V_IN = 0 or 3 V
Room - 0.001 - 0.1
Full
-1
Ground Current
I_GND
Room - 0.001 - 0.1
Full
-1
- 40 to 85 °C
Min.^d Max.^d
0
3
235
280
- 0.1 0.1
- 0.25 0.25
- 0.1 0.1
- 0.25 0.25
- 0.1 0.1
- 0.25 0.25
- 0.1 0.1
- 0.1 0.1
125
170
55
60
10
0.1
1
- 0.1
-1
- 0.1
-1
Unit
V
Ω
nA
µA
pF
ns
pC
dB
MHz
pF
µA
Notes:
a. V_IN = input voltage to perform proper function.
b. Room = 25 °C, Full = as determined by the operating temperature suffix.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
e. Guaranteed by design, not subject to production test.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
www.vishay.com
6
Document Number: 69904
S-72760-Rev. A, 04-Feb-08