ILD620GB-X009T Datasheet, PDF (3/9 Pages) Vishay Siliconix – Optocoupler, Phototransistor Output, AC Input (Dual, Quad Channel)

www.vishay.com
ILD620, ILD620GB, ILQ620, ILQ620GB
Vishay Semiconductors
ELECTRICAL CHARACTERISTICS (T_amb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
PART
SYMBOL MIN. TYP. MAX. UNIT
COUPLER
Off-state collector current
Collector emitter saturation voltage
V_F = ± 0.7 V, V_CE = 24 V
I_F = ± 8 mA, I_CE = 2.4 mA
I_F = ± 1 mA, I_CE = 0.2 mA
ILD620
ILQ620
ILD620GB
ILQ620GB
I_CEoff
V_CEsat
V_CEsat
V_CEsat
V_CEsat
1
10
μA
0.4
V
0.4
V
0.4
V
0.4
V
Note
• Minimum and maximum values are testing requirements. Typical values are characteristics of the device and are the result of engineering
evaluation. Typical values are for information only and are not part of the testing requirements.
CURRENT TRANSFER RATIO (T_amb = 25 °C, unless otherwise specified)
PARAMETER
TEST CONDITION
PART
SYMBOL
Channel/channel CTR match
CTR symmetry
Current transfer ratio 
(collector emitter saturated)
Current transfer ratio 
(collector emitter)
Current transfer ratio 
(collector emitter saturated)
Current transfer ratio 
(collector emitter)
I_F = ± 5 mA, V_CE = 5 V
I_CE (I_F = - 5 mA)/I_CE (I_F = + 5 mA)
I_F = ± 1 mA, V_CE = 0.4 V
I_F = ± 5 mA, V_CE = 5 V
I_F = ± 1 mA, V_CE = 0.4 V
I_F = ± 5 mA, V_CE = 5 V
ILD620
ILQ620
ILD620
ILQ620
ILD620GB
ILQ620GB
ILD620GB
ILQ620GB
CTRX/CTRY
I_CE(RATIO)
CTR_CEsat
CTR_CEsat
CTR_CE
CTR_CE
CTR_CEsat
CTR_CEsat
CTR_CEsat
CTR_CEsat
MIN.
1 to 1
0.5
50
50
30
30
100
100
TYP.
60
60
80
80
200
200
MAX.
3 to 1
2
600
600
600
600
UNIT
%
%
%
%
%
%
%
%
SAFETY AND INSULATION RATED PARAMETERS
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
MAX.
UNIT
Partial discharge test voltage -
routine test
100 %, t_test = 1 s
V_pd
1.669
kV
Partial discharge test voltage -
t_Tr = 60 s, t_test = 10 s,
V_IOTM
10
kV
lot test (sample test)
(see figure 2)
V_pd
1.424
kV
V_IO = 500 V
R_IO
10¹²

Insulation resistance
V_IO = 500 V, T_amb = 100 °C
R_IO
10¹¹

V_IO = 500 V, T_amb  150 °C
(construction test only)
R_IO
10⁹

Forward current
Power dissipation
Rated impulse voltage
Safety temperature
I_si
P_SO
V_IOTM
T_si
275
mA
400
mW
10
kV
175
°C
Note
• According to DIN EN 60747-5-5 (VDE 0884) (see figure 2). This optocoupler is suitable for safe electrical isolation only within the safety
ratings. Compliance with the safety ratings shall be ensured by means of suitable protective circuits.
Rev. 1.8, 12-Apr-13
3
Document Number: 83653
For technical questions, contact: [e-mail]
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000