DG528_11 Datasheet, PDF (3/12 Pages) Vishay Siliconix – Latchable Single 8-Ch/Differential 4-Ch Analog Multiplexers

DG528, DG529
Vishay Siliconix
SPECIFICATIONS^a
Parameter
Analog Switch
Analog Signal Range^e
Drain-Source
On-Resistance
Greatest Change in R_DS(on)
Between Channels^f
Source Off Leakage Current
Symbol
V_ANALOG
R_DS(on)
R_DS(on)
I_S(off)
Drain Off Leakage Current
I_D(off)
Drain On Leakage Current
Digital Control
I_D(on)
Test Conditions
Unless Otherwise Specified
V+ = 15 V, V- = - 15 V, WR = 0,
RS = 2.4 V, V_IN = 2.4 V, 0.8 µF^f
A Suffix B, C, D Suffix
- 55 °C to 125 °C - 40 °C to 85 °C
Temp.^b Typ.^c Min.^d Max.^d Min.^d Max.^d Unit
V_D = ± 10 V, I_S = - 200 µA
Full
- 15 15 - 15 15
V
Room 270
Full
400
500
450
550

- 10 V < V_S < 10 V
Room 6
%
V_EN = 0 V, V_D = ± 10 V
V_S = ± 10 V
Room ^{± 005} - 1
1
-5
5
Full
- 50 50 - 50 50
V_EN = 0 V, V_D = ± 10 V
DG528
Room
Full
± 0.015
- 10
- 200
10
200
- 20
- 200
20
200
V_S = ± 10 V
DG529
Room
Full
± 0.008
- 10
- 100
10
100
- 20
- 100
20
100
nA
V_S = V_D = ± 10 V
V_EN = 2.4 V
DG528
Room
Full
± 0.03
- 10
- 200
10
200
- 20
- 200
20
200
DG529
Room
Full
± 0.015
- 10
- 100
10
100
- 20
- 100
20
100
Logic Input Current
I_AH
Input Voltage High
Logic Input Current
Input Voltage Low
I_AL
Dynamic Characteristics
V_A = 2.4 V
V_A = 15 V
V_EN = 0 V, 2.4 V, V_A = 0 V
RS = 0 V, WR = 0 V
Room - 0.002 - 10
- 10
Hot
- 30
- 30
Room 0.006
10
Hot
30
10
30
µA
Room - 0.002 - 10
- 10
Hot
- 30
- 30
Transition Time
t_TRANS
See Figure 5
Room 0.6
1
Break-Before-Make Interval
t_OPEN
See Figure 4
Room 0.2
µs
EN and WR Turn-On Time t_ON(EN,WR)
See Figure 6 and 7
Room 1
1.5
EN and WR Turn-Off Time t_OFF(EN,RS)
See Figure 6 and 8
Room 0.4
1
Charge Injection
Q
V_S = 0 V, R_y = 0 C_L = 10 F
Room
4
pC
Off Isolation
OIRR
V_EN = 0 V, R_L = 1 kC_L = 15 pF
V_S = 7 V_RMS, f = 500 kHz
Room
68
dB
Logic Imput Capacitance
C_in
f = 1 MHz
Room 2.5
Source Off Capacitance
Drain Off Capacitance
C_S(off)
C_D(off)
V_EN = 0 V, V_D = 0 V, f = 140 kHz
Room
5
V_EN = 0 V, V_D = 0 V
f = 140 kHz
DG528 Room 25
DG529 Room 12
pF
Minimum Input Timing Requirements
Write Pulse Width
t_W
A_X, EN Data Set Up time
t_S
A_X, EN Data Hold Time
t_H
Reset Pulse Width
t_RS
Power Supplies
Positive Supply Current
I+
Negative Supply Current
I-
V_S = 5 V, See Figure 3
V_EN = V_A = 0 V
Full
Full
Full
Full
Room
Room
300
300
180
180
ns
30
30
500
500
2.5
2.5
mA
- 1.5
- 1.5
Notes:
a. Refer to PROCESS OPTION FLOWCHART.
b. Room = 25 °C, Full = as determined by the operating temperature suffix.
c. Typical values are for DESIGN AID ONLY, not guaranteed nor subject to production testing.
d. The algebraic convention whereby the most negative value is a minimum and the most positive a maximum, is used in this data sheet.
e. Guaranteed by design, not subject to production test.
f. V_IN = input voltage to perform proper function.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation
of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum
rating conditions for extended periods may affect device reliability.
Document Number: 70068
www.vishay.com
S11-1029–Rev. D, 23-May-11
3
This document is subject to change without notice.
THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000