English
Language : 

VS-ST380CH Datasheet, PDF (2/8 Pages) Vishay Siliconix – Metal case with ceramic insulator
◁
www.vishay.com
VS-ST380CH Series
Vishay Semiconductors
ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
Maximum average on-state current
at heatsink temperature
IT(AV)
Maximum RMS on-state current
IT(RMS)
Maximum peak, one-cycle
non-repetitive surge current
ITSM
Maximum I2t for fusing
I2t
Maximum I2√t for fusing
Low level value of threshold voltage
High level value of threshold voltage
Low level value of on-state slope resistance
High level value of on-state slope resistance
Maximum on-state voltage
Maximum holding current
Typical latching current
I2√t
VT(TO)1
VT(TO)2
rt1
rt2
VTM
IH
IL
TEST CONDITIONS
180° conduction, half sine wave
double side (single side) cooled
DC at 25 °C heatsink temperature double side cooled
t = 10 ms
t = 8.3 ms
No voltage
reapplied
t = 10 ms
t = 8.3 ms
t = 10 ms
t = 8.3 ms
100 % VRRM
reapplied
No voltage
reapplied
Sinusoidal half wave,
initial TJ = TJ maximum
t = 10 ms
t = 8.3 ms
100 % VRRM
reapplied
t = 0.1 to 10 ms, no voltage reapplied
(16.7 % x π x IT(AV) < I < π x IT(AV)), TJ = TJ maximum
(I > π x IT(AV)), TJ = TJ maximum
(16.7 % x π x IT(AV) < I < π x IT(AV)), TJ = TJ maximum
(I > π x IT(AV)), TJ = TJ maximum
Ipk = 2900 A, TJ = TJ maximum, tp = 10 ms sine pulse
TJ = 25 °C, anode supply 12 V resistive load
VALUES
960 (440)
80 (110)
2220
12 500
13 000
10 500
11 000
782
713
553
505
7820
0.85
0.88
0.25
0.24
1.58
600
1000
UNITS
A
°C
A
kA2s
kA2√s
V
mΩ
V
mA
SWITCHING
PARAMETER
Maximum non-repetitive rate of rise
of turned-on current
Typical delay time
Typical turn-off time
BLOCKING
PARAMETER
Maximum critical rate of rise of
off-state voltage
Maximum peak reverse and
off-state leakage current
SYMBOL
dI/dt
td
tq
TEST CONDITIONS
Gate drive 20 V, 20 Ω, tr ≤ 1 μs
TJ = TJ maximum, anode voltage ≤ 80 % VDRM
Gate current 1 A, dIg/dt = 1 A/μs
Vd = 0.67 % VDRM, TJ = 25 °C
ITM = 550 A, TJ = TJ maximum, dI/dt = 40 A/μs,
VR = 50 V, dV/dt = 20 V/μs, gate 0 V 100 Ω, tp = 500 μs
VALUES
1000
1.0
100
UNITS
A/µs
µs
SYMBOL
dV/dt
IRRM,
IDRM
TEST CONDITIONS
TJ = TJ maximum linear to 80 % rated VDRM
TJ = TJ maximum, rated VDRM/VRRM applied
VALUES UNITS
500
V/µs
100
mA
Revision: 20-Dec-13
2
Document Number: 94411
For technical questions within your region: DiodesAmericas@vishay.com, DiodesAsia@vishay.com, DiodesEurope@vishay.com
THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT
ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000
 ▷