S102C Datasheet, PDF (2/6 Pages) Vishay Siliconix – High Precision Foil Resistor with TCR of ± 2.0 ppm/°C, Tolerance of ± 0.005 % and Load Life Stability of ± 0.005 %

S Series
Vishay Foil Resistors ^{High Precision Foil Resistor with TCR of ± 2.0 ppm/°C,}
Tolerance of ± 0.005 % and Load Life Stability of ± 0.005 %
FIGURE 2 - STANDARD IMPRINTING AND DIMENSIONS
Front View
Rear View
L
Optional Customer Part Number
W
Print specification, etc. if required
Date Code
VISHAY 01 10
H
XXXX Year Week
S102C
XXXXXX
100R01
0.01 %
Resistance
Value Code
Tolerance
ST¹⁾
Model Number
SW
LL
LS
Lead Material #22 AWG
Round Solder Coated Copper
Note
1. The standoffs shall be so located as to give a lead clearance of 0.010" minimum between the resistor body and the printed circuit board
when the standoffs are seated on the printed circuit board. This is to allow for proper cleaning of flux and other contaminants from the unit
after all soldering processes.
TABLE 2 - MODEL SELECTION
MODEL
NUMBER
RESISTANCE MAXIMUM
RANGE WORKING
(Ω)
VOLTAGE
AMBIENT
POWER RATING AVERAGE
WEIGHT
at
at IN GRAMS
+ 70 °C + 125 °C
DIMENSIONS
INCHES
mm
F¹⁾
(INCHES)
TIGHTEST
TOLERANCE
VS. LOWEST
RESISTANCE
VALUE
S102C
(S102J)²⁾
1 to 150K
S102K
(S102L)²⁾
1 to 100K
0.6 W 0.3 W
W: 0.105 ± 0.010 2.67 ± 0.25
up to 100K
L: 0.300 ± 0.010 7.62 ± 0.25
300
0.4 W 0.2 W
0.6
H: 0.326 ± 0.010 8.28 ± 0.25
ST: 0.010 min. 0.254 min.
SW: 0.035 ± 0.010 1.02 ± 0.13
over 100K
LL: 1.000 ± 0.125 25.4 ± 3.18
LS: 0.150 ± 0.0054 3.81 ± 0.13
S104D
(S104F)¹⁾
1 to 500K
S104K
1 to 300K
S105D
(S105F)¹⁾
1 to 750K
S105K
1 to 500K
1.0 W 0.5 W
W: 0.160 max.
4.06 max.
up to 200K
L: 0.575 max. 14.61 max.
350
0.6 W 0.3 W
H: 0.413 max. 10.49 max. (0.138)
1.4
ST: 0.035 ± 0.005 0.889 ± 0.13
SW: 0.050 ± 0.005 1.27 ± 0.13
(0.565)
(0.413)
0.005 %/50 Ω
over 200K
LL: 1.000 ± 0.125 25.4 ± 3.18
LS: 0.400 ± 0.020 10.16 ± 0.51
0.01 %/25 Ω
0.02 %/12 Ω
0.05 %/5 Ω
1.5 W 0.75 W
up to 300K
0.8 W 0.4 W
W: 0.160 max.
L: 0.820 max.
H: 0.413 max.
4.06 max.
20.83 max.
10.49 max.
(0.138)
(0.890)
(0.413)
0.1 %/2 Ω
0.25 %/2 Ω
0.50 %/1 Ω
350
1.9
ST: 0.035 ± 0.005 0.889 ± 0.13
1.0 %/1 Ω
SW: 0.050 ± 0.005 1.27 ± 0.13
over 300K
LL: 1.000 ± 0.125 25.4 ± 3.18
LS: 0.650 ± 0.020 16.51 ± 0.51
(0.7 ±
0.02)
S106D
0.5 to 1M
2.0 W 1.0 W
W: 0.260 max.
6.60 max.
up to 400K
L: 1.200 max. 30.48 max.
500
1.0 W 0.5 W
H: 0.413 max. 10.49 max.
4.0
ST: 0.035 ± 0.005 0.889 ± 0.13
S106K
0.5 to 600K
over 400K
SW: 0.050 ± 0.005 1.27 ± 0.13
LL: 1.000 ± 0.125 25.4 ± 3.18
LS: 0.900 ± 0.020 22.86 ± 0.51
Notes
1. S104F and S105F have different package dimensions (see last column). All other specifications are the same.
2. 0.200" (5.08 mm) lead spacing available - specify S102J for S102C, and S102L for S102K.
www.vishay.com
2
For any questions, contact: [e-mail]
Document Number: 63001
Revision: 20-Nov-07