DFP14121K00GD05 Datasheet, PDF (2/3 Pages) Vishay Siliconix – Thick Film Resistor Networks Flat Pack, 11, 12 Schematics

Thick Film Resistor Networks
Flat Pack, 11, 12 Schematics
DFP
Vishay Dale
DIMENSIONS in inches [millimeters]
Pin #1
0.050
[1.27]
Typ.
0.019 ± 0.006
[0.48 ± 0.15]
0.365 [9.27] Min.
0.385 [9.78] Max.
0.265 [6.73] Max.
GLOBAL MODEL
DFP14
DFP16
0.065
[1.65]
Max.
0.250 [6.35]
Min.
0.250 [6.35]
Min.
0.825 [20.96]
Max.
0.005 + 0.004
- 0.002
[0.127 + 0.102
- 0.051]
DIMENSION A
0.037 ± 0.010 [0.94 ± 0.25]
0.012 ± 0.010 [0.30 ± 0.25]
TECHNICAL SPECIFICATIONS
PARAMETER
UNIT
Isolation Resistance 11 Schematic
MΩ
Voltage Coefficient of Resistance
ppm/V
Maximum Operating Voltage
VDC
Operating Temperature Range
°C
Storage Temperature Range
°C
11 Schematic
DFP14/16
> 100
< 50 typical
75
- 55 to + 125
- 55 to + 150
MECHANICAL SPECIFICATIONS
Marking
Model number, schematic number, value
tolerance, pin 1 indicator, date code.
Marking Resistance Permanency testing per MIL-STD-202
to Solvents
Method 215.
Solderability
Terminals
Per MIL-STD-202, Method 208E.
Per MIL-STD-1276 DFPxx11, DFPxx12 =
Type G (hot solder dipped). Hot solder
dipped leads supplied as standard finish.
Body
Epoxy filled ceramic sandwich
12 Schematic
Package
0.65
Package
0.65
0.50
0.50
Single Resistor
0.25
Single Resistor
0.15
- 55
Derating
+ 25
+ 70 + 125 + 150
Ambient Temperature °C
- 55
Derating
+ 25
+ 70 + 125 + 150
Ambient Temperature °C
PERFORMANCE
TEST
Power Conditioning
Thermal Shock
Short Time Overload
Low Temperature Operation
Moisture Resistance
Resistance to Soldering Heat
Shock
Vibration
Load Life
Terminal Strength
Insulation Resistance
Dielectric Withstanding
Voltage
CONDITIONS
MAX. ΔR (Typical Test Lots)
1.5 x rated power, applied 1.5 hours “ON” and 0.5 hour “OFF”
for 100 hours ± 4 hours at + 25 °C ambient temperature
± 0.50 % ΔR
5 cycles between - 65 °C and + 125 °C
± 0.50 % ΔR
2.5 x rated working voltage, 5 seconds
± 0.25 % ΔR
45 minutes at full rated working voltage at - 65 °C
± 0.25 % ΔR
240 hours with humidity ranging from 80 % RH to 98 % RH
± 0.50 % ΔR
Leads immersed in + 260 ° ΔC solder to within 1/16" of body for 10 seconds
Total of 18 shocks at 100 g's
± 0.25 % ΔR
± 0.25 % ΔR
12 hours at maximum of 20 g's between 10 and 2000 Hz
± 0.25 % ΔR
1000 hours at + 70 °C, rated power applied 1.5 hours “ON”, 0.5 hour “OFF”
for full 1000 hour period. Derated according to the curve.
± 0.50 % ΔR
1.5 pound pull for 30 seconds
± 0.25 % ΔR
10 000 Megohm (minimum)
-
No evidence of arcing or damage (200 V RMS for 1 minute)
-
Document Number: 31513
Revision: 08-Sep-04
For technical questions, contact: [e-mail]
www.vishay.com
329