SI9135 Datasheet, PDF (13/14 Pages) Vishay Siliconix – SMBus Multi-Output Power-Supply Controller

New Product
Si9135
Vishay Siliconix
Normal Operation: Buck Converters
In normal operation, the buck converter high-side MOSFET is
turned on with a delay (known as break-before-make time -
t_BBM), after the rising edge of the clock. After a certain on
time, the high-side MOSFET is turned off and then after a
delay (t_BBM), the low-side MOSFET is turned on until the next
rising edge of the clock, or the inductor current reaches zero.
The t_BBM (approximately 25 ns to 60 ns), has been optimized
to guarantee the efficiency is not adversely affected at the
high switching frequency and a specified minimum to account
for variations of possible MOSFET gate capacitances.
During the normal operation, the high-side MOSFET switch
on-time is controlled internally to provide excellent line and
load regulation over temperature. Both buck converters
should have load, line, regulation to within 0.5% tolerance.
Pulse Skipping: Buck Converters
When the buck converter switching frequency is less than the
internal clock frequency, its operation mode is defined as
pulse skipping mode. During this mode, the high-side
MOSFET is turned on until V_CS-V_FB reaches 20 mV, or the on
time reaches its maximum duty ratio. After the high-side
MOSFET is turned off, the low-side MOSFET is turned on
after the t_BBM delay, which will remain on until the inductor
current reaches zero. The output voltage will rise slightly
above the regulation voltage after this sequence, causing the
controller to stay idle for the next one, or several clock cycles.
When the output voltage falls slightly below the regulation
level, the high-side MOSFET will be turned on again at the
next clock cycle. With the converter remaining idle during
some clock cycles, the switching losses are reduced in order
to preserve conversion efficiency during the light output
current condition.
Current Limit: Buck Converters
When the buck converter inductor current is too high, the
voltage across pin CS3(5) and pin FB3(5) exceeds
approximately 120 mV, the high-side MOSFET would be
turned off instantaneously regardless of the input, or output
condition. The Si9135 features clock cycle by clock cycle
current limiting capability.
Flyback Converter Operation
Designed mainly for PCMCIA or EEPROM programming, the
Si9135 has a 12-V output non-isolated buck boost converter,
called for brevity a flyback. It consists of two n-channel
MOSFET switches that are turned on and off in phase, and
two diodes. Similar to the buck converter, during the light load
conditions, the flyback converter will switch at a frequency
lower than the internal clock frequency, which can be defined
as pulse skipping mode (PSM); otherwise, it is operating in
normal PWM mode.
Normal Operation: Flyback Converter
In normal operation mode, the two MOSFETs are turned on at
the rising edge of the clock, and then turned off. The on time
is controlled internally to provide excellent load, line, and
temperature regulation. The flyback converter has load, line
and temperature regulation well within 0.5%.
Pulse Skipping: Flyback Converter
Under the light load conditions, similar to the buck converter,
the flyback converter will enter pulse skipping mode. The
MOSFETs will be turned on until the inductor current
increases to such a level that the voltage across the pin CSP
and pin CSN reaches 100 mV, or the on time reaches the
maximum duty cycle. After the MOSFETs are turned off, the
inductor current will conduct through two diodes until it
reaches zero. At this point, the flyback converter output will
rise slightly above the regulation level, and the converter will
stay idle for one or several clock cycle(s) until the output falls
back slightly below the regulation level. The switching losses
are reduced by skipping pulses and so the efficiency during
light load is preserved.
Current Limit: Flyback Converter
Similar to the buck converter; when the voltage across pin
CSP and pin CSN exceeds 410-mV typical, the two
MOSFETs will be turned off regardless of the input and
output conditions.
SMBus Commands
After completion of startup, Si9135’s converters can be
individually or as a group commanded on or off using a code
word on the SMBus, as detailed in the SMBus Truth Table.
The command sequence is:
A. Receive a start bit, which is a falling edge on the
SDA line while the SCL line is high.
B. Receive a one-byte address, which for Si9135 is
01100000.
C. Send an acknowledge bit.
D. Receive a one-byte command.
E. Send an acknowledge bit.
F. Receive a stop bit, which is a rising edge on the SDA
line while the SCL line is high.
This is a total of 20 bits, which at the maximum clock
frequency of 100 kHz translates into 200 µsec before any
change in the status of Si9135 ban be accomplished.
If Si9135 receives a command to turn on (respectively, off) a
converter that is already on (respectively, off) it shall not
falsely command the converter off (respectively, on).
Si9135 must be able to receive a stop command at any time
during a command sequence. If Si9135 receives a stop
command during a command sequence, it must not change
the state of any converter, and must be ready to receive the
next command sequence.
FaxBack 408-970-5600, request 70817
www.siliconix.com
S-60752—Rev. B, 05-Apr-99
13