B048X240Y30A Datasheet, PDF (12/18 Pages) Vicor Corporation – Unregulated DC-DC Converter

Not Recommended for New Designs
B048x240y30A
This is similar in form to Eq. (3), where R_OUT is used to
represent the characteristic impedance of the SAC™. However,
in this case a real R on the input side of the SAC is effectively
scaled by K² with respect to the output.
Assuming that R = 1 Ω, the effective R as seen from the secondary
side is 250.0 mΩ, with K = 1/2 .
A similar exercise should be performed with the additon of a
capacitor or shunt impedance at the input to the SAC.
A switch in series with V_IN is added to the circuit. This is
depicted in Figure 15.
S
V_VINin
+
–
C
S_SA_AC_C™
K^K=⁼1¹/3^/22
VV_OUo_Tut
Figure 15 — Sine Amplitude Converter™ with input capacitor
A change in V_IN with the switch closed would result in a
change in capacitor current according to the following
equation:
I_C(t)
=
C ^dVIN
dt
(7)
Assume that with the capacitor charged to V_IN, the switch is
opened and the capacitor is discharged through the idealized
SAC. In this case,
I_C= I_OUT • K
(8)
Low impedance is a key requirement for powering a high-
current, low-voltage load efficiently. A switching regulation
stage should have minimal impedance while simultaneously
providing appropriate filtering for any switched current. The
use of a SAC between the regulation stage and the point of
load provides a dual benefit of scaling down series impedance
leading back to the source and scaling up shunt capacitance or
energy storage as a function of its K factor squared. However,
the benefits are not useful if the series impedance of the SAC
is too high. The impedance of the SAC must be low, i.e. well
beyond the crossover frequency of the system.
A solution for keeping the impedance of the SAC low involves
switching at a high frequency. This enables small magnetic
components because magnetizing currents remain low. Small
magnetics mean small path lengths for turns. Use of low loss
core material at high frequencies also reduces core losses.
The two main terms of power loss in the BCM module are:
- No load power dissipation (P_NL): defined as the power
used to power up the module with an enabled powertrain
at no load.
- Resistive loss (R_OUT): refers to the power loss across
the BCM module modeled as pure resistive impedance.
P_DISSIPATED = P_NL + P_ROUT
(10)
Therefore,
P_OUT = P_IN – P_DISSIPATED = P_IN – P_NL – P_ROUT
(11)
The above relations can be combined to calculate the overall
module efficiency:
h
=
P_OUT
P_IN
=
P_IN – P_NL – P_ROUT
P_IN
(12)
substituting Eq. (1) and (8) into Eq. (7) reveals:
I_OUT
=
C
K²
•
dV_OUT
dt
(9)
The equation in terms of the output has yielded a K² scaling
factor for C, specified in the denominator of the equation.
A K factor less than unity results in an effectively larger
capacitance on the output when expressed in terms of the
input. With a K = 1/2 as shown in Figure 15,
C=1 µF would appear as C=4 µF when viewed
from the output.
=
V_IN • I_IN – P_NL – (I_OUT)² • R_OUT
V_IN • I_IN
( ) ⁼
1–
P_NL + (I_OUT)² • R_OUT
V_IN • I_IN
BCM^® Bus Converter
Page 12 of 18
Rev 1.1
11/2014
vicorpower.com
800 927.9474