 English |
|
|
|
|
|
|
|
| CD4066 Datasheet, PDF (5/8 Pages) Unisonic Technologies – QUAD BILATERAL SWITCH | |||
| |||
| ◁ |
CD4066
CMOS IC
 AC ELECTRICAL CHARACTERISTICS
(TA=25°C, tR=tF=20nS and VSS=0V, unless otherwise specified) (Note 1)
PARAMETER
SYMBOL
TEST CONDITIONS
MIN TYP MAX UNIT
Propagation Delay Time Signal
tPHL, tPLH
VCON=VDD, CL=5pF,
RL=200k⦠(Fig. 1)
VDD=5V
VDD=10V
VDD=15V
25 55 ns
15 35 ns
10 25 ns
Propagation Delay Time
Control Input to Signal
Output High Impedance to Logical Level
tPZH, tPZL
RL=1kâ¦, CL=50pF,
(Fig. 2, 3)
VDD=5V
VDD=10V
VDD=15V
125 ns
60 ns
50 ns
Propagation Delay Time
Control Input to Signal
Output Logical Level to High Impedance
tPHZ, tPLZ
RL=1kâ¦, CL=50pF,
(Fig. 2, 3)
VDD=5V
VDD=10V
VDD=15V
125 ns
60 ns
50 ns
Sine Wave Distortion
VCON=VDD=5V, VSS=-5V, RL=10kâ¦,
0.1
%
VIS=5Vp-p, f=1kHz (Fig. 4)
Frequency Response-Switch âONâ
(Frequency at -3dB)
VCON=VDD=5V, VSS=-5V, RL=1kâ¦,
20 Log10(VOS/VIS)=-3dB,
VIS=5.0Vp-p (Fig. 4)
40
MHz
Feedthrough - Switch âOFFâ
(Frequency at -50dB)
VDD=5.0V, VCC=VSS=-5.0V,
RL=1kâ¦, VIS=5.0Vp-p,
20 Log10(VOS/VIS)=-50dB (Fig. 4)
1.25
MHz
Crosstalk Between Any Two Switches
(Frequency at -50dB)
VDD=VCON(A)=5.0V, RL=1kâ¦,
VSS=VCON (B)=5.0V, VIS(A)=5.0Vp-p,
0.9
MHz
20 Log10(VOS(B)/VIS(A))=-50dB(Fig. 5)
Crosstalk, Control Input to Signal Output
VDD=10V, RL=10kâ¦, RIN=1kâ¦,
VCC=10V Square Wave,
CL=50pF (Fig. 6)
150
mVP-
P
Maximum Control Input
RL=1kâ¦, CL=50pF,
VOS(f)=½ VOS(1kHz)
(Fig. 7)
VDD=5V
VDD=10V
VDD=15V
6
MHz
8
MHz
8.5
MHz
Signal Input Capacitance
CIS
8.0
pF
Signal Output Capacitance
COS VDD=10V
8.0
pF
Feedthrough Capacitance
CIOS
VCON=0V
0.5
pF
Control Input Capacitance
CIN
5.0 7.5 pF
Notes:1. AC Parameters are guaranteed by DC correlated testing.
2. These devices should not be connected to circuits with the power âONâ.
3. In all cases, there is approximately 5 pF of probe and jig capacitance in the output; however, this
capacitance is included in CL wherever it is specified.
4. VIS is the voltage at the in/out pin and VOS is the voltage at the out/in pin. VCON is the voltage at the control
input.
5. Conditions for VIHC:
a) VIS=VDD, IOS=standard B series IOH
b) VIS=0V, IOL= standard B series IOL
UNISONIC TECHNOLOGIES CO., LTD
www.unisonic.com.tw
5 of 8
QW-R502-739.A
|
▷ |
German
Russian
Spanish
Italian
Polish
Chinese
Japanese
Korean
French
Portuguese