QP-375_17 Datasheet, PDF (4/7 Pages) Total Power International – 375W Quad Output with PFC Function

Authorized Distributor: Total Power International, Inc. Toll Free: 877-646-0900(US) PH# [phone] www.total-power.com
375W Quad Output with PFC Function
QP-375-24 series
Features :
Universal AC input / Full range
Built-in active PFC function, PF>0.95
Protections: Short circuit / Overload / Over voltage / Over temperature
Forced air cooling by built-in DC fan
CH3,4 are isolated from other outputs and the polarity can be reversed
No minimum load requirement for CH2,3,4
All output can be adjustable from -5~+10%
With power good and fail signal output
Built-in remote ON-OFF control
Fixed switching frequency at 100KHz
SPECIFICATION
3 years warranty
..
MODEL
QP-375-24B
QP-375-24C
OUTPUT
OUTPUT NUMBER
CH1
CH2
DC VOLTAGE
+24V
+5V
RATED CURRENT
10A
10A
CURRENT RANGE
1 ~ 10A
0 ~ 16A
RATED POWER(max.)
386W
RIPPLE & NOISE (max.) Note.2 240mVp-p
50mVp-p
VOLTAGE ADJ. RANGE
21.6 ~ 26.4V 4.5 ~ 5.5V
VOLTAGE TOLERANCE Note.3 1.0%
1.0%
LINE REGULATION
0.5%
0.5%
LOAD REGULATION
0.8%
0.8%
SETUP, RISE TIME
800ms, 50ms at full load
CH3
12V
4A
0 ~ 4A
120mVp-p
10.8 ~ 13.2V
1.0%
0.5%
0.8%
CH4
12V
4A
0 ~ 4A
120mVp-p
10.8 ~ 13.2V
1.0%
0.5%
0.8%
CH1
+24V
10A
1 ~ 10A
410W
240mVp-p
21.6 ~ 26.4V
1.0%
0.5%
0.8%
CH2
+5V
10A
0 ~ 10A
50mVp-p
4.5 ~ 5.5V
1.0%
0.5%
0.8%
CH3
15V
4A
0 ~ 4A
CH4
15V
4A
0 ~ 4A
150mVp-p
13.5 ~ 16.5V
1.0%
0.5%
0.8%
150mVp-p
13.5 ~ 16.5V
1.0%
0.5%
0.8%
HOLD UP TIME (Typ.)
36ms at full load
VOLTAGE RANGE Note.7 85 ~ 264VAC
FREQUENCY RANGE
47 ~ 63Hz
120 ~ 370VDC
POWER FACTOR (Typ.)
PF>0.95/230VAC PF>0.98/115VAC at full load
INPUT
EFFICIENCY (Typ.)
78%
80%
AC CURRENT (Typ.)
6A/115VAC 3A/230VAC
INRUSH CURRENT (Typ.) COLD START 45A
LEAKAGE CURRENT
<2mA / 240VAC
OVERLOAD
105 ~ 135% rated output power
Protection type : Hiccup mode, recovers automatically after condition is removed
PROTECTION OVER VOLTAGE
CH1:27.6 ~ 32.4V
Protection type : Shut down o/p voltage, re-power on to recover
OVER TEMPERATURE
80 5 (TSW1) Detect on heatsink of Q1,Q2 power transistor)
Protection type : Shut down o/p voltage, recovers automatically after temperature goes down
POWER GOOD / POWER FAIL(OPTIONAL) 10ms/1ms
FUNCTION
REMOTE CONTROL
RC+/RC-:0 ~ 0.8V POWER ON; 4V ~ 10V POWER OFF
WORKING TEMP.
-10 ~ +60 (Refer to output load derating curve)
WORKING HUMIDITY
20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -20 ~ +85 , 10 ~ 95% RH
TEMP. COEFFICIENT
0.03%/ (0~50 )
VIBRATION
10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes
SAFETY STANDARDS
UL60950-1, TUV EN60950-1 Approved
SAFETY &
EMC
(Note 4)
WITHSTAND VOLTAGE
ISOLATION RESISTANCE
EMI CONDUCTION & RADIATION
HARMONIC CURRENT
I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC
Compliance to EN55022 (CISPR22) Class B
Compliance to EN61000-3-2,-3
EMS IMMUNITY
Compliance to EN61000-4-2,3,4,5,6,8,11; ENV50204, EN55024, Light industry level, criteria A
MTBF
75.9K hrs min. MIL-HDBK-217F (25 )
OTHERS
NOTE
DIMENSION
280*127*63.5mm (L*W*H)
PACKING
2.4Kg; 6pcs/14.8Kg/1.45CUFT
1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25 of ambient temperature.
2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
5. Peak current can not exceed 60 sec.
6. Isolated CH3 & CH4 maybe series connected or can be used as positive or negative outputs.
7. Derating may be needed under low input voltages. Please check the derating curve for more details.