TLP2168_15 Datasheet, PDF (3/16 Pages) Toshiba Semiconductor – Inverter logic type (open collector output)

TLP2168
7. Absolute Maximum Ratings (Note) (Unless otherwise specified, T_a = 25 )
Characteristics
Symbol Note
Rating
Unit
LED Input forward current
I_F
(Note 1)
25
mA
Input forward current derating
(T_a ≥ 110 )
∆I_F/∆T_a (Note 1)
-0.67
mA/
Input forward current (pulsed)
I_FP (Note 1),
40
mA
(Note 2)
Input forward current derating (pulsed)
(T_a ≥ 110 )
∆I_FP/∆T_a (Note 1)
-1.0
mA/
Input reverse voltage
V_R
(Note 1)
5
V
Input power dissipation
P_D
(Note 1)
40
mW
Detector Output current
I_O
(Note 1)
25
mA
Output voltage
V_O
(Note 1)
6
V
Supply voltage
V_CC
6
V
Output power dissipation
P_O
(Note 1)
40
mW
Output power dissipation derating
(T_a ≥ 110 )
∆P_O/∆T_a (Note 1)
-1
mW/
Common Operating temperature
T_opr
-40 to 125

Storage temperature
T_stg
-55 to 150

Lead soldering temperature
(10 s)
T_sol
260

Isolation voltage
AC, 60 s, R.H. ≤ 60 %
BV_S (Note 3)
2500
Vrms
Note: Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the
significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even
if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum
ratings.
Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook
("Handling Precautions"/"Derating Concept and Methods") and individual reliability data (i.e. reliability test
report and estimated failure rate, etc).
Note 1: Each channel
Note 2: Pulse width (PW) ≤ 1 ms, duty = 50 %
Note 3: This device is considered as a two-terminal device: Pins 1, 2, 3 and 4 are shorted together, and pins 5, 6, 7
and 8 are shorted together.
8. Recommended Operating Conditions (Note)
Characteristics
Symbol Note Min Typ. Max Unit
Input on-state current
I_F(ON) (Note 1), 7.5

14
mA
(Note 2)
Input off-state voltage
V_F(OFF) (Note 1)
0

0.8
V
Supply voltage
V_CC
(Note 3) 2.7 3.3/5.0 5.5
Operating temperature
T_opr
-40

125

Note: The recommended operating conditions are given as a design guide necessary to obtain the intended
performance of the device. Each parameter is an independent value. When creating a system design using
this device, the electrical characteristics specified in this datasheet should also be considered.
Note: A ceramic capacitor (0.1 µF) should be connected between pin 8 and pin 5 to stabilize the operation of a high-
gain linear amplifier. Otherwise, this photocoupler may not switch properly. The bypass capacitor should be
placed within 1 cm of each pin.
Note 1: Each channel
Note 2: The rise and fall times of the input on-current should be less than 0.5 µs.
Note 3: Denotes the operating range, not the recommended operating condition.
©2015 Toshiba Corporation
3
2015-12-10
Rev.6.0