XC6416 Datasheet, PDF (5/30 Pages) Torex Semiconductor – Dual LDO Voltage Regulator with “GreenOperation”

XC6416
Series




˙ELECTRICAL
CHARACTERISTICS

_{˔XC6416A/B/E/F Series}


Regulator 1, Regulator 2
PARAMETER
SYMBOL
CONDITIONS
Output Voltage 1 (HS*)
V_OUT1(E)(*2)
V_OUT(T)ʾ2.0V, (A/B Series)
V_EN=V_IN, I_OUT=10mA
V_OUT(T)ʽ1.95V, (A/B Series)
V_EN=V_IN, I_OUT=10mA
V_OUT(T)ʾ1.5VʢE/F Series)
V_EN=V_IN, I_OUT=10mA
V_OUT(T)ʽ1.45VʢE/F Series)
V_EN=V_IN, I_OUT=10mA
Ta=25ˆ
MIN.
×0.99
(*3)
TYP.
MAX.
×1.01
(*3)
UNITS CIRCUITS
- 0.02
+ 0.02
(*3)
(*3)
×0.98
V_OUT(T)
(*4)
×1.02
V
ᶃ
(*3)
(*3)
- 0.03
(*3)
+ 0.03
(*3)
V_OUT(T)ʾ2.0V,
×0.97
×1.03
Output Voltage 2 (PS*)
V_OUT2(E)(*2)
V_EN=V_IN, I_OUT=0.1mA
V_OUTʽ1.95V,
(*3)
- 0.06
V_OUT(T)
(*4)
(*3)
+ 0.06
V
ᶃ
V_EN=V_IN, I_OUT=0.1mA
(*3)
(*3)
Output Current
I_OUTMAX
200
-
-
mA
ᶃ
Load Regulation
ΔV_OUT VEN=VIN, 10mAʽIOUTʽ100mA
E-1
mV
ᶃ
Dropout Voltage ^(*5)
Vdif
I_OUT=100mA, V_EN=V_IN
E-2
mV
ᶃ
Supply Current 1 (HS*)
I_SS1
V_IN=V_EN=V_OUT(T)+1.0V,
-
28
60
ЖA
ᶄ
Supply Current 2 (PS*)
I_SS2
V_IN=V_EN= V_OUT(T)+1.0V,
-
5.0
12
ЖA
ᶄ
Stand-by Current
I_STBY
V_IN=6.0V, V_EN=V_SS
-
0.01 0.1
ЖA
ᶄ
Line Regulation 1 (HS*)
ΔV_OUT/
(ΔV_INɾV_OUT)
V_OUT(T)+0.5VʽV_INʽ6.0V
V_OUT(T)ʾ1.0V, V_EN=V_IN,
I_OUT=10mA
1.5VʽV_INʽ6.0V
V_OUT(T)ʽ0.95V, V_EN=V_IN,
I_OUT=10mA
-
0.01 0.2
%/V
ᶃ
Input Voltage
V_IN
1.5
-
6.0
V
ᶃ
Output Voltage
ΔV_OUT/
Temperature Characteristics (ΔTaɾV_OUT)
V_EN=V_IN, I_OUT=30mA
-40ˆʽTaʽ85ˆ
-
±100
-
ppm/ˆ
ᶃ
Ripple Rejection Rate
PSRR VIN=ʨVOUT(T)+1.0ʩ VDC+0.5Vp-pAC
-
60
-
dB
ᶅ
Limit Current
I_LIM
V_EN=V_IN
210 300
-
mA
ᶃ
Short Current
I_SHORT V_EN=V_IN, Short V_OUT to V_SS level
-
20
-
mA
ᶃ
PS Switching Current
I_GOR
V_EN=V_IN, I_OUT=Heavy to light load 0.25
1.5


mA
ᶃ
HS Switching Current
I_GO
V_EN=V_IN, I_OUT=Light to heavy load


4
7.5
mA
ᶃ
Switching Current Hysteresis
PS Switching Delay Time
I_GOhys
t_DPS
I_GOhys=I_GO-I_GOR
V_EN=V_IN,


2.5


mA
ᶃ
E-3
Жs
ᶃ
EN High Level Voltage
V_ENH


1.2


6
V
ᶃ
EN Low Level Voltage
V_ENL






0.3
V
ᶃ
EN High Level Current
I_ENH
V_EN=V_IN
-0.1


0.1
ЖA
ᶃ
EN Low Level Current
I_ENL
V_EN=V_SS
-0.1


0.1
ЖA
ᶃ
C_L Discharge Resistance^(*8)
R_DCHG
V_IN=6.0V, V_OUT=4.0V, V_EN=V_SS


550


Ω
ᶃ


NOTE:
*HS: High Speed Mode, PS: Power Save Mode
*1: Unless otherwise stated, V_IN=V_{OUT (T)} +1.0V.
*2: V_{OUT (E)}= Nominal output voltage (see the voltage chart)
(ie. The output voltage when lV_{OUT (T)} +1.0Vz is provided at the V_IN pin while maintaining a certain I_OUT value.
*3
: Characteristics of the effective V_OUT(E) by nominal output voltage is shown in the voltage chart.
*4
: V_OUT(T)
: Nominal output voltage
*5: Vdifʹ{V_IN1(*7)ʵV_OUT1(*6)}
*6: V_OUT1: A voltage equal to 98% of the V_{OUT (T)} when an amply stabilized V_{OUT (T)} +1.0V is input.
*7: V_IN1: The input voltage when the V_OUT1 voltage appears at the V_OUT pin during decreasing input voltage gradually.
*8: For XC6416xB/Bx/xF/Fx series only.
XC6416xA/Ax/xE/Ex series discharge with only Rx1 and Rx2 resistors as shown in the BLOCK DIAGRAMS.
*9: When each channel is measured, the other channel is turned off (V_EN=V_SS).
5/30