SM73301 Datasheet, PDF (6/22 Pages) Texas Instruments – RRIO, High Output Current & Unlimited Cap Load Op Amp in SOT23-5

Symbol
Parameter
A_VOL
Large Signal Voltage Gain
V_O
Output Swing
High
Output Swing
Low
I_SC
Output Short Circuit Current
I_S
SR
f_u
GBWP
Supply Current
Slew Rate
(Note 8)
Unity Gain Frequency
Gain-Bandwidth Product
Phi_m
e_n
i_n
f_MAX
t_s
Phase Margin
Input-Referred Voltage Noise
Input-Referred Current Noise
Full Power Bandwidth
Settling Time (±1%, A_V = +1)
THD+N Total Harmonic Distortion +Noise
Condition
V_O = 0V to ±13V,
R_L = 10KΩ
V_O = 0V to ±13V,
R_L = 2KΩ
R_L = 10KΩ
R_L = 2KΩ
R_L = 10KΩ
R_L = 2KΩ
Sourcing to ground
V_ID = 200mV (Note 10)
Sinking to ground
V_ID = 200mV (Note 10)
No load, V_CM = 0V
A_V = +1, V_I = 24V_PP
V_I = 10mV, R_L = 2KΩ
f = 50KHz
V_I = 10mV
f = 2KHz, R_S = 50Ω
f = 2KHz
Z_L = 20pF || 10KΩ
Positive Step, 5V_PP
Negative Step, 5V_PP
R_L = 1KΩ, f = 10KHz,
A_V = +2, 28V_PP swing
Typ
(Note 5)
85
79
14.83
14.73
−14.91
−14.83
60
100
1.30
15
14
24
58
15
1
160
320
600
0.01
Limit
(Note 6)
78
74
72
66
14.65
14.61
14.60
14.55
−14.75
−14.65
−14.65
−14.60
40
25
70
60
1.50
1.90
10
8
–
18
16
–
–
–
–
–
–
–
Units
dB
min
V
min
V
max
mA
min
mA
max
V/µs
min
MHz
MHz
min
Deg
nV/
pA/
KHz
ns
%
Note 1: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Rating indicate conditions for which the device is
intended to be functional, but specific performance is not guaranteed. For guaranteed specifications and the test conditions, see the Electrical Characteristics.
Note 2: Human Body Model is 1.5kΩ in series with 100pF.
Note 3: Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the
maximum allowed junction temperature of 150°C.
Note 4: The maximum power dissipation is a function of T_J(max), θ_JA, and T_A. The maximum allowable power dissipation at any ambient temperature is
P_D = (T_J(MAX) - T_A)/ θ_JA. All numbers apply for packages soldered directly onto a PC board.
Note 5: Typical Values represent the most likely parametric norm.
Note 6: All limits are guaranteed by testing or statistical analysis.
Note 7: Positive current corresponds to current flowing into the device.
Note 8: Slew rate is the slower of the rising and falling slew rates. Connected as a Voltage Follower.
Note 9: Machine Model, 0Ω is series with 200pF.
Note 10: Short circuit test is a momentary test. See Note 11.
Note 11: Output short circuit duration is infinite for V_S ≤ 6V at room temperature and below. For V_S > 6V, allowable short circuit duration is 1.5ms.
Note 12: Offset voltage average drift determined by dividing the change in V_OS at temperature extremes into the total temperature change.
Note 13: Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very limited self-heating
of the device such that T_J = T_A. No guarantee of parametric performance is indicated in the electrical tables under conditions of internal self heating where T_J >
T_A.
5
www.national.com