TSB43AB23PDTG4 Datasheet, PDF (55/110 Pages) Texas Instruments – IEEE 1394a-2000 OHCI PHY/Link Layer Controller 

BIT
22
21–20
19
18
17
16
15–0
Table 4–11. Host Controller Control Register Description (Continued)
FIELD NAME
aPhyEnhanceEnable
TYPE
RSC
DESCRIPTION
When bits 23 (programPhyEnable) and 17 (linkEnable) are 1, the OHCI driver can set bit 22 to
1 to use all IEEE 1394a-2000 enhancements. When bit 23 (programPhyEnable) is cleared to 0,
the software does not change PHY enhancements or this bit.
RSVD
LPS
postedWriteEnable
R
RSC
RSC
Reserved. Bits 21 and 20 return 0s when read.
Bit 19 controls the link power status. Software must set this bit to 1 to permit the link-PHY
communication. A 0 prevents link-PHY communication.
The OHCI-link is divided into two clock domains (PCI_CLK and PHY_SCLK). If software tries to
access any register in the PHY_SCLK domain while the PHY_SCLK is disabled, a target abort
is issued by the link. This problem can be avoided by setting bit 4 (DIS_TGT_ABT) to 1 in the
miscellaneous configuration register at offset F0h in the PCI configuration space (see
Section 3.21, Miscellaneous Configuration Register). This allows the link to respond to these
types of request by returning all Fs (hex).
OHCI registers at offsets DCh–F0h and 100h–11Ch are in the PHY_SCLK domain.
After setting LPS, software must wait approximately 10 ms before attempting to access any of
the OHCI registers. This gives the PHY_SCLK time to stabilize.
Bit 18 enables (1) or disables (0) posted writes. Software changes this bit only when bit 17
(linkEnable) is 0.
linkEnable
RSC
Bit 17 is cleared to 0 by either a system (hardware) or software reset. Software must set this bit
to 1 when the system is ready to begin operation and then force a bus reset. This bit is necessary
to keep other nodes from sending transactions before the local system is ready. When this bit is
cleared, the TSB43AB23 device is logically and immediately disconnected from the 1394 bus, no
packets are received or processed, nor are packets transmitted.
SoftReset
RSVD
RSCU
R
When bit 16 is set to 1, all TSB43AB23 states are reset, all FIFOs are flushed, and all OHCI
registers are set to their system (hardware) reset values, unless otherwise specified. PCI
registers are not affected by this bit. This bit remains set to 1 while the software reset is in progress
and reverts back to 0 when the reset has completed.
Reserved. Bits 15–0 return 0s when read.
4.17 Self-ID Buffer Pointer Register
The self-ID buffer pointer register points to the 2K-byte aligned base address of the buffer in host memory where the
self-ID packets are stored during bus initialization. Bits 31–11 are read/write accessible. Bits 10–0 are reserved, and
return 0s when read.
Bit
31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16
Name
Self-ID buffer pointer
Type
R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W R/W
Default X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
Bit
15 14 13 12 11 10
9
8
7
6
5
4
3
2
1
0
Name
Self-ID buffer pointer
Type
R/W R/W R/W R/W R/W R
R
R
R
R
R
R
R
R
R
R
Default X
X
X
X
X
0
0
0
0
0
0
0
0
0
0
0
Register:
Offset:
Type:
Default:
Self-ID buffer pointer
64h
Read/Write, read-only
XXXX XX00h
4–14