LMC8101 Datasheet, PDF (5/26 Pages) National Semiconductor (TI) – Rail-to-Rail Input and Output, 2.7V Op Amp in micro SMD package with Shutdown

LMC8101
www.ti.com
SNOS496F – AUGUST 2000 – REVISED MARCH 2013
±5V Electrical Characteristics (continued)
Unless otherwise specified, all limits specified for T_J = 25°C, V⁺ =5V, V^− = −5V, V_CM = V_O = 0V, and R_L > 1 MΩ to gnd.
Boldface limits apply at the temperature extremes.
Symbol
Parameter
Conditions
Typ ⁽¹⁾
Limit ⁽²⁾
Units
A_VOL
Large Signal Voltage Gain
V_O
Output Swing High
Output Swing Low
I_SC
Output Short Circuit Current
Sourcing
R_L = 600Ω
V_O = 0V to 4V
Sinking
R_L = 600Ω
V_O = 0V to −4V
Sourcing
R_L = 2kΩ
V_O = 0V to 4.6V
Sinking
R_L = 2kΩ
V_O = 0V to −4.6V
R_L = 600Ω
V_ID = 100mV
R_L = 2kΩ
V_ID = 100mV
R_L = 600Ω
V_ID = −100mV
R_L = 2kΩ
V_ID = −100mV
Sourcing, V_ID = 100mV⁽⁴⁾⁽⁵⁾
Sinking, V_ID = −100mV⁽⁴⁾⁽⁵⁾
34.5
34.5
138
138
4.73
4.90
−4.85
−4.95
49
90
17.8
10
17.8
3.16
31.6
17.8
31.6
10
4.60
4.54
4.85
4.83
−4.75
−4.65
4.90
−4.84
30
25
60
52
V/mV
min
V/mV
min
V
min
V
min
V
max
V
max
mA
min
mA
min
I_S
T_on
T_off
I_in
SR
f_u
GBW
Supply Current
Shutdown Turn-on time
Shutdown Turn-off time
"SL" and "SD" Input Current
Slew Rate⁽⁷⁾
Unity Gain-Bandwidth
Gain Bandwidth Product
No load, normal operation
Shutdown mode
See ⁽⁶⁾
See ⁽⁶⁾
A_V = +10, R_L = 10kΩ,
V_O = 10Vpp, C_L = 1000pF
V_I = 10mV
R_L = 2kΩ
f = 10KHz
1.1
0.001
10
1
±1
1.2
840
1.3
1.7
mA
1.9
max
1
µA
15
µs
µs
±64
pA max
V/µs
KHz
MHz
e_n
Input-Referred Voltage Noise
f = 10KHz, R_s = 50Ω
33
i_n
Input-Referred Current Noise
f = 10KHz
1.5
THD
Total Harmonic Distortion
f = 10KHz, AV = +1,
V_O =8Vpp, R_L = 600Ω
0.2
nV/√Hz
fA/√Hz
%
(4) Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in
exceeding the maximum allowed junction temperature at 150°C. Output currents in excess of 40mA over long term may adversely affect
reliability.
(5) Short circuit test is a momentary test. Output short circuit duration is infinite for V_S < 6V. Otherwise, extended period output short circuit
may damage the device.
(6) Shutdown Turn-on and Turn-off times are defined as the time required for the output to reach 90% and 10%, respectively, of its final
peak to peak swing when set for Rail to Rail output swing with a 100KHz sine wave, 2KΩ load, and A_V = +10.
(7) Slew rate is the slower of the rising and falling slew rates.
Copyright © 2000–2013, Texas Instruments Incorporated
Product Folder Links: LMC8101
Submit Documentation Feedback
5