AMC1306E05_017 Datasheet, PDF (5/38 Pages) Texas Instruments – Small, High-Precision, Reinforced Isolated Delta-Sigma Modulators with High CMTI

www.ti.com
AMC1306E05, AMC1306E25, AMC1306M05, AMC1306M25
SBAS734A – MARCH 2017 – REVISED JULY 2017
7.6 Insulation Specifications
over operating ambient temperature range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VALUE UNIT
GENERAL
CLR External clearance⁽¹⁾
CPG External creepage⁽¹⁾
Shortest pin-to-pin distance through air
Shortest pin-to-pin distance across the package surface
≥9
mm
≥9
mm
DTI Distance through insulation
Minimum internal gap (internal clearance) of the double insulation
(2 × 0.0105 mm)
≥ 0.021
mm
CTI Comparative tracking index
DIN EN 60112 (VDE 0303-11); IEC 60112
≥ 600
V
Material group
According to IEC 60664-1
I
Rated mains voltage ≤ 300 V_RMS
I-IV
Overvoltage category per IEC 60664-1 Rated mains voltage ≤ 600 V_RMS
I-IV
Rated mains voltage ≤ 1000 V_RMS
I-III
DIN V VDE V 0884-11 (VDE V 0884-11): 2017-01⁽²⁾
V_IORM
Maximum repetitive peak isolation
voltage
At ac voltage (bipolar)
2121
V_PK
V_IOWM
V_IOTM
V_IOSM
q_pd
C_IO
R_IO
Maximum-rated isolation working
voltage
Maximum transient isolation voltage
Maximum surge isolation voltage⁽³⁾
Apparent charge⁽⁴⁾
Barrier capacitance, input to output⁽⁵⁾
Insulation resistance, input to output⁽⁵⁾
Pollution degree
At ac voltage (sine wave)
At dc voltage
V_TEST = V_IOTM, t = 60 s (qualification test)
V_TEST = 1.2 × V_IOTM, t = 1 s (100% production test)
Test method per IEC 60065, 1.2/50-μs waveform,
V_TEST = 1.6 × V_IOSM = 12800 V_PK (qualification)
Method a, after input/output safety test subgroup 2/3,
V_ini = V_IOTM, t_ini = 60 s,
V_pd(m) = 1.2 × V_IORM = 2545 V_PK, t_m = 10 s
Method a, after environmental tests subgroup 1,
V_ini = V_IOTM, t_ini = 60 s,
V_pd(m) = 1.6 × V_IORM = 3394 V_PK, t_m = 10 s
Method b1, at routine test (100% production) and preconditioning
(type test), V_ini = V_IOTM, t_ini = 1 s,
V_pd(m) = 1.875 × V_IORM = 3977 V_PK, t_m = 1 s
V_IO = 0.5 V_PP at 1 MHz
V_IO = 500 V at T_A = 25°C
V_IO = 500 V at 100°C ≤ T_A ≤ 125°C
V_IO = 500 V at T_S = 150°C
1500
2121
7000
8400
8000
≤5
V_RMS
V_DC
V_PK
V_PK
≤5
pC
≤5
~1
pF
> 10¹²
> 10¹¹
Ω
> 10⁹
2
Climatic category
40/125/21
UL1577
V_ISO Withstand isolation voltage
V_TEST = V_ISO = 5000 V_RMS or 7000 V_DC, t = 60 s (qualification),
V_TEST = 1.2 × V_ISO = 6000 V_RMS, t = 1 s (100% production test)
5000
V_RMS
(1) Apply creepage and clearance requirements according to the specific equipment isolation standards of an application. Care must be
taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the isolator on the printed
circuit board (PCB) do not reduce this distance. Creepage and clearance on a PCB become equal in certain cases. Techniques such as
inserting grooves and ribs on the PCB are used to help increase these specifications.
(2) This coupler is suitable for safe electrical insulation only within the safety ratings. Compliance with the safety ratings shall be ensured by
means of suitable protective circuits.
(3) Testing is carried out in air or oil to determine the intrinsic surge immunity of the isolation barrier.
(4) Apparent charge is electrical discharge caused by a partial discharge (pd).
(5) All pins on each side of the barrier are tied together, creating a two-pin device.
Copyright © 2017, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: AMC1306E05 AMC1306E25 AMC1306M05 AMC1306M25