MSP430BT5190 Datasheet, PDF (43/99 Pages) Texas Instruments – MIXED SIGNAL MICROCONTROLLER

MSP430BT5190
www.ti.com
SLAS703 – APRIL 2010
Outputs – General Purpose I/O (Full Drive Strength)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
V_OH High-level output voltage
V_OL Low-level output voltage
TEST CONDITIONS
I_(OHmax) = –3 mA ⁽¹⁾
I_(OHmax) = –10 mA ⁽²⁾
I_(OHmax) = –5 mA⁽¹⁾
I_(OHmax) = –15 mA⁽²⁾
I_(OLmax) = 3 mA ⁽¹⁾
I_(OLmax) = 10 mA⁽²⁾
I_(OLmax) = 5 mA ⁽¹⁾
I_(OLmax) = 15 mA⁽²⁾
V_CC
1.8 V
3V
1.8 V
3V
MIN
V_CC – 0.25
V_CC – 0.60
V_CC – 0.25
V_CC – 0.60
V_SS
V_SS
V_SS
V_SS
MAX
V_CC
V_CC
V_CC
V_CC
V_SS + 0.25
V_SS + 0.60
V_SS + 0.25
V_SS + 0.60
UNIT
V
V
(1) The maximum total current, I_(OHmax) and I_(OLmax), for all outputs combined should not exceed ±48 mA to hold the maximum voltage drop
specified.
(2) The maximum total current, I_(OHmax) and I_(OLmax), for all outputs combined should not exceed ±100 mA to hold the maximum voltage
drop specified.
Outputs – General Purpose I/O (Reduced Drive Strength)
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)⁽¹⁾
PARAMETER
V_OH High-level output voltage
V_OL Low-level output voltage
TEST CONDITIONS
I_(OHmax) = –1 mA ⁽²⁾
I_(OHmax) = –3 mA ⁽³⁾
I_(OHmax) = –2 mA⁽²⁾
I_(OHmax) = –6 mA⁽³⁾
I_(OLmax) = 1 mA ⁽²⁾
I_(OLmax) = 3 mA ⁽³⁾
I_(OLmax) = 2 mA ⁽²⁾
I_(OLmax) = 6 mA ⁽³⁾
V_CC
1.8 V
3.0 V
1.8 V
3.0 V
MIN
MAX
V_CC – 0.25
V_CC – 0.60
V_CC – 0.25
V_CC – 0.60
V_SS
V_SS
V_SS
V_SS
V_CC
V_CC
V_CC
V_CC
V_SS + 0.25
V_SS + 0.60
V_SS + 0.25
V_SS + 0.60
UNIT
V
V
(1) Selecting reduced drive strength may reduce EMI.
(2) The maximum total current, I_(OHmax) and I_(OLmax), for all outputs combined, should not exceed ±48 mA to hold the maximum voltage drop
specified.
(3) The maximum total current, I_(OHmax) and I_(OLmax), for all outputs combined, should not exceed ±100 mA to hold the maximum voltage
drop specified.
Output Frequency – General Purpose I/O
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
f_Px.y
Port output frequency
(with load)
P1.6/SMCLK ^{(1) (2)}
V_CC = 1.8 V
PMMCOREVx = 0
V_CC = 3 V
PMMCOREVx = 3
f_{Port_CLK} Clock output frequency
P1.0/TA0CLK/ACLK
P1.6/SMCLK
P2.0/TA1CLK/MCLK
C_L = 20 pF⁽²⁾
V_CC = 1.8 V
PMMCOREVx = 0
V_CC = 3 V
PMMCOREVx = 3
MAX UNIT
16
MHz
25
16
MHz
25
(1) A resistive divider with 2 × R1 between V_CC and V_SS is used as load. The output is connected to the center tap of the divider. For full
drive strength, R1 = 550 Ω. For reduced drive strength, R1 = 1.6 kΩ. C_L = 20 pF is connected to the output to V_SS.
(2) The output voltage reaches at least 10% and 90% V_CC at the specified toggle frequency.
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
43