DRV8848_16 Datasheet, PDF (4/27 Pages) Texas Instruments – Dual H-Bridge Motor Driver

DRV8848
SLLSEL7A – OCTOBER 2014 – REVISED NOVEMBER 2015
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range referenced with respect to GND (unless otherwise noted) ⁽¹⁾
MIN
MAX
Power supply voltage (VM)
–0.3
20
Power supply voltage ramp rate (VM)
0
2
Internal regulator voltage (VINT)
–0.3
3.6
Analog input pin voltage (VREF)
–0.3
3.6
Control pin voltage (AIN1, AIN2, BIN1, BIN2, nSLEEP, nFAULT)
–0.3
7
Continuous phase node pin voltage (AOUT1, AOUT2, BOUT1, BOUT2)
Continuous shunt amplifier input pin voltage (AISEN, BISEN)⁽²⁾
–0.3
–0.6
V_VM + 0.6
0.6
Peak drive current (AOUT1, AOUT2, BOUT1, BOUT2, AISEN, BISEN)
Internally limited
T_J
Operating junction temperature
T_stg Storage temperature
–40
150
–65
150
UNIT
V
V/µs
V
V
V
V
V
A
°C
°C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) Transients of ±1 V for less than 25 ns are acceptable.
6.2 ESD Ratings
V_(ESD)
Electrostatic
discharge
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001, all pins⁽¹⁾
Charged device model (CDM), per JEDEC specification JESD22-C101, all pins⁽²⁾
VALUE
±4000
±1500
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
UNIT
V
6.3 Recommended Operating Conditions
MIN
V_VM
Power supply voltage range⁽¹⁾
4
V_VREF
Reference rms voltage range⁽²⁾
1
ƒ_PWM
Applied STEP signal
0
I_VINT
VINT external load current
I_rms
Motor rms current per H-bridge⁽³⁾
0
T_A
Operating ambient temperature
–40
(1) Note that R_DS(ON) increases and maximum output current is reduced at VM supply voltages below 5 V.
(2) Operational at VREF between 0 and 1 V, but accuracy is degraded.
(3) Power dissipation and thermal limits must be observed.
MAX
18
3.3
250
1
1
85
UNIT
V
V
kHz
mA
A
°C
6.4 Thermal Information
THERMAL METRIC⁽¹⁾
DRV8848
PWP (HTSSOP)
UNIT
16 PINS
R_θJA
R_θJC(top)
R_θJB
ψ_JT
ψ_JB
R_θJC(bot)
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
40.3
°C/W
32.7
°C/W
28.7
°C/W
0.6
°C/W
11.4
°C/W
4.7
°C/W
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report, SPRA953.
4
Submit Documentation Feedback
Product Folder Links: DRV8848
Copyright © 2014–2015, Texas Instruments Incorporated